3. Insert part (7) and part (4) and attach them by pushing in part (6) in a transverse/sideways
direction (= open position).
4. Press the nuts (13) in part (9) and assemble it to part (7) with the screws M4x20 (11).
5. Put the preassembled X-creen onto the windscreen and attach it with the nuts (13), the cover
(10) and the screws M4x8 (12) to the provided drilled holes.
6. Tighten the screws M4x20 (11) of the mounting feet FXC-3 (9).
C - Drilling the Windscreen to the mount the X-creen:
Drill your windscreen only if you are sure you want to mount the X-creen spoiler permanently. Please
note it is also possible to clamp the X-creen onto your windscreen using the optionally available XCC
Tension Clamp Brackets kit (Art. No. 4025066125074) – no drilling is required with these (see section
D below).
1. Place the provided drilling template on the outside of the windscreen to be drilled so that
the two arrows on the template are flush with the windscreen edge and that the template is
centred. The scale on the left and on the right of the template (P1) will help you.
2. Take the preassembled X-creen spoiler, put the mounting feet (9) in a parallel position and
lock the adjusting buttons (2) or (6). Hold the X-creen spoiler on top of the drilling template
and check if the markings correspond with the mounting points of the X-creen (P2).
When doing so, the mounting feet (9) must be turned so that they lie flat on the
windscreen’s outer surface. If the markings on the template do not correspond with the
mounting holes, draw in suitable markings now.
3. Drill the 6mm holes with care and light pressure through the template into the windscreen.
Make sure you drill vertically to the windscreen surface and do not slip (sticking one or more
layers of clear tape on the screen’s surface before you mark and drill may assist with this).
4. Put the preassembled X-creen onto the windscreen and attach it with the nuts (13), the
cover (10) and the screws M4x8 (12) to the provided drilled holes.
5. Tighten the screws M4x20 (11) of the mounting feet FXC-3 (9).
D - Mounting the X-creen spoiler using the XCC Tension Clamp Brackets kit:
If you would prefer not to drill your windscreen, you can mount the X-creen spoiler on your
windscreen using the optionally available XCC tension clamp brackets kit (Art. No. 4025066125074).
You will need 2.5 mm, 3mm and 4 mm Allen keys and a 10 mm combination spanner for assembly
and installation.
1. Take the preassembled X-creen spoiler, put the mounting feet (9) in parallel position and lock
the adjusting buttons (2) or (6).
2. Screw the coverings (10) with the screws M4x8 (12) to one side of the XCC brackets (14). On
the opposite side, screw the XCC brackets to the mounting feet (9) of the X-creen.
3. Press the rubber washers (15) on the thread end of the screws M4x8 (12). If you wish, you may
glue the rubber washers onto the XCC brackets with contact adhesive (such as Evo Stick
Impact), as this will make the assembly process easier.
4. Put the rubber hoses (16) into the XCC brackets, push the screws M6x30 (17) through them
and screw the nuts M6 (18) with the washers (19) on them.
5. Now put the X-creen centrally onto the windscreen so that the rubber hoses are on the edge
of the windscreen.
6. Tighten the screws using their corresponding tools, making sure that the XCC brackets stay in
the required position so that the joints are not under tension.
To Next Page
Loading...