To Next PageTo Next Page
Need help?Do you have a question about the Nature Air RGRM-06*MAES and is the answer not in the manual?
General| Brand | Nature Air |
|---|---|
| Model | RGRM-06*MAES |
| Category | Furnace |
| Language | English |
Safety requirements for side wall horizontally vented gas appliances in MA.
Exemptions from Massachusetts safety requirements for gas appliances.
Manufacturer requirements for supplied venting systems.
Manufacturer requirements for non-supplied venting systems.
Requirement to keep installation instructions with the appliance.
General considerations for furnace installation location.
Guidelines for selecting a suitable installation site.
Clearances required for furnace installation and service access.
Instructions for ducting upflow furnace units.
Instructions for ducting downflow furnace units.
Instructions for ducting horizontal furnace units.
General principles for venting and combustion air.
Function and reset of overtemperature safety switches.
Guidelines for connecting to existing vent systems.
Proper procedure for cementing pipe joints.
Combustion and ventilation air for non-direct installations.
Combustion air requirements for unconfined spaces.
Combustion air requirements for confined spaces.
How to use indoor air for combustion.
Method 1 for providing outdoor combustion air.
Method 2 for providing outdoor combustion air.
Connecting combustion air to the furnace.
General guidelines for non-direct vent installations.
Instructions for alternate elevated tee termination.
Guidelines for standard installation methods.
Location requirements for non-direct vent terminations.
General guidelines for direct vent installations.
Specific combustion air requirements for direct vent systems.
Requirements for standard direct vent terminations.
Options for alternate direct vent terminations.
Information on concentric vent termination types.
Details for installing the concentric vent kit.
Assembly instructions for sidewall concentric vents.
Installation instructions for concentric vents on roofs.
Guidelines for venting multiple furnaces.
Specifics for the RXGY-G02 side wall vent.
Connecting combustion air and vent pipes for upflow furnaces.
Connecting combustion air and vent pipes for downflow/horizontal furnaces.
General information about condensate drainage.
Details of the condensate drain system for upflow models.
Steps to reverse the condensate trap for upflow units.
Instructions for converting downflow condensate trap.
Instructions for horizontal installation of condensate drain.
Instructions for filling the condensate trap.
Important information regarding gas supply.
Guidelines for installing gas piping.
Information on the gas valve's function and settings.
Instructions for installing LP gas orifices.
Procedure for changing burner orifices.
Steps to convert the gas valve and adjust pressure for LP gas.
Final steps after completing the LP gas conversion.
How to set the heat anticipator.
Information on optional accessories.
When and how to install an isolation relay.
Connecting an electronic air cleaner.
Connecting a humidifier.
High altitude adjustments for natural gas.
High altitude adjustments for LP gas.
Information on ordering orifices.
Instructions for starting the furnace with direct spark ignition.
Step-by-step procedure to start the furnace.
Step-by-step procedure to shut down the furnace.
Proper placement and alignment of the ignitor.
Description of the furnace's operational sequence.
How single-stage thermostats control the furnace.
Procedure when calling for first stage heat.
Procedure when calling for second stage heat.
Adjustments for cooling airflow settings.
Selecting two-stage cooling mode.
Adjusting continuous fan settings.
How the dehumidification feature works.
Procedure to check the temperature rise.
How to maintain air filters.
Information on filters and their placement.
Advice to give to the customer.
Recommended annual inspection items.
Introduction to troubleshooting procedures.
Indication of 24VAC power to the control board.
Indication of target airflow.
Reference to the furnace wiring diagram.
Warning about hazardous voltage and line connections.
Key to abbreviations used in the troubleshooting chart.
Explanation of status LED blink codes.
Explanation of flame LED codes.
Starting the troubleshooting process.
Checks during the pre-purge phase.
Checks during the ignition trial phase.
Checks during the Indoor Blower Motor "On" delay.
Checks for steady low heat operation.
Checks when the heat call ends.
Checks during the post-purge phase.
Checks during the Indoor Blower Motor "Off" delay.
Checks for steady off state.
