Item
No.
Item Input Data Description Default Related
Program
09 Private Line 0 = Disable Private
Line (Normal)
1 = Enable Private Line
(Private Line)
0
10 DTMF Tones for
Outgoing Calls
0 = Disable (No)
1 = Enable (Yes)
Use this option to enable (1) or disa-
ble (0) DTMF tones for outgoing
trunk calls.
0
11 Account Code
Required
0 = Disabled (user can-
not enter account co-
des using this trunk.)
1 = Enabled (user can
enter account codes
using this trunk.)
Per trunk enable or disable the abili-
ty to enter an account code on an
inbound or outbound trunk call.
1
13 Trunk-to-Trunk
Transfer
0 = Disable (No)
1 = Enable (Yes)
Use this option to enable (1) or disa-
ble (0) loop supervision for the
trunk. This option is required for Call
Forwarding Off-Premise and T
an-
dem Trunking only.
1
14 Long Conversa-
tion Cutoff
0 = Disable (No)
1 = Enable (Yes)
Use this option to enable or disable
the Long Conversation Cutoff fea-
ture for each trunk.
0 20-21-03
20-21-04
15 Long Conversa-
tion Alarm Be-
fore Cutoff
0 = Disable (No)
1 = Enable (Yes)
Use this option to enable or disable
the Long Conversation Alarm for
each trunk.
0 20-21-01
20-21-02
16 Forced Release
of Held Call
0 = Disable (No)
1 = Enable (Yes)
Use this option to enable/disable
forced release for calls on Hold. If
enabled, the system disconnects a
call if it is on Hold longer than a pro-
grammed interval (Program
24-01-05). If disabled, forced dis-
connection does not occur. Program
24-01-01 also affects this option.
0 24-01-01
24-01-05
17 Trunk to Trunk
Warning Tone for
Long Conversa-
tion Alarm
0 = Disable (No)
1 = Enable (Yes)
Use this option to enable or disable
the Warning Tone for Long Conver-
sation feature for DISA callers.
0
18 Warning Beep
Tone Signaling
0 = Disable (No)
1 = Enable (Yes)
0
19 Privacy Mode
Toggle Option
0 = Disable (No)
1 = Enable (Yes)
Use this option to enable or disable
a trunk ability to be switched from
private to non-private mode by
pressing the line key or Privacy Re-
lease function key.
0
20 Block Outgoing
Caller ID
0 = Prevent (No)
1 = Allow (Yes)
Allow (1) or prevent (0) the system
from automatically blocking outgoing
Caller ID information when a user
places a call. If allowed (i.e. block,
enabled), the system automatically
inserts the Caller ID block code (de-
fined in 14-01-21) before the user
dialed digits.
0
14-01-21
20-08-15
21 Caller ID Block
Code
Dial (up to eight dig-
its)
Enter the code, up to 8 digits, that
should be used as the Caller ID
Block Code. This code is automati-
cally inserted before dialed digits if
Program 14-01-20 is set to 1.
67 14-01-20
20-08-15
22 Caller ID to Voice
Mail
0 = Disable (Caller ID
not sent to VM.)
1 = Enable (Caller ID is
sent to VM.)
Enable or disable the system ability
to send the Caller ID digits (Remote
Log-On Protocol) to voice mail.
0
ISSUE 2.0 SL2100
Programming Manual 2-115
Program
14
To Next Page
Loading...
