Newport wi Series - Display Color Examples

To Next Page

To Previous Page

4.3.7.5.1 Display Color Examples

Example 1:

Output 1 & Output 2

= SSR

Alarm Setup

: Absolute, Above, Alarm 2 HI Value "

AALLRR..HH

" = 200,

Alarm 1 HI Value "

AALLRR..HH

" = 400

"Color Display" Setup

: Normal Color “

NN..CCLLRR

” = Green,

Alarm 1 Color "

11..CCLLRR

" = Amber, Alarm 2 Color "

22..CCLLRR

" = Red

Display Colors change sequences:

GREEN RED AMBER

•

➤

------------------------------

•

-----------------------------

•

------------------------------

➤

0 AL2.H = 200 AL1.H = 400

Example 2:

Output 1 & Output 2

= Pulse

Alarm Setup

: Absolute, Below, Alarm 2 Low Value "

AALLRR..LL

" = 300,

Alarm 1 Low Value "

AALLRR..LL

" = 100

Color Display Setup

: "

NN..CCLLRR

" = Green, "

11..CCLLRR

" = Amber, "

22..CCLLRR

" = Red

Display Colors change sequences:

AMBER RED GREEN

•

--------------

•

----------------------------------

•

------------------------------------------- --

•

0 AL1.L = 100 AL2.L = 300

➤ ➤

Main Page

Table of Contents3
Part 1 Introduction7
Safety Considerations7
Before You Begin8
Description9
Figure 1.1 Temperature Wireless Monitor and Control System10
Part 2 Hardware11
Physical Characteristics and Mounting11
Front Panel11
Figure 2.1 Front Panel Display11
Table 2.1 Front Panel Enunciators11
Rear Panel12
Figure 2.2 Rear Panel Power and Output Connections12
Table 2.2 Rear Panel Connector12
Dimensions13
Figure 2.3 Mounting Dimensions13
Assembly and Mounting14
Panel Mounting Instruction14
Figure 2.4 Panel Mounting14
Antenna Mounting Instruction15
Figure 2.5 Antenna Mounting15
Disassembly Instruction16
Figure 2.6 Accessing the Main Board Assembly16
Electrical Installation17
Power Connections17
Figure 2.7 Main Power Connections17
Table 2.3 Fuse Requirements (See Specifications)17
Wiring Outputs18
Figure 2.8A Mechanical Relay and SSR Output Wiring Hookup18
Figure 2.8B Pulse and Analog Output Wiring Hookup18
Figure 2.9 Typical Applications19
Jumper Settings for Display Color Setup20
Figure 2.10 Location of S1 Jumper20
DIP Switches21
Figure 2.11 Location of DIP Switches21
Network Communications22
10Base-T RJ45 Pinout22
10Base-T Crossover Wiring22
Figure 2.12 RJ45 Pinout22
Figure 2.13 10Base-T Crossover Cable Wiring22
Part 3 Network Configuration23
Ethernet (MAC) Address23
Network Protocols23
Dhcp23
Figure 3.1 Label Detail23
Dns24
Figure 3.2 4 Position DIP Switch24
IP Address25
Default IP Address25
Changing TCP/IP Properties on Your Computer26
Figure 3.3 Network Connections26
Figure 3.4 Network Connections26
Part 4 Network Operations27
Testing the Connection27
Figure 4.1 Pinging the Meter from MS-DOS Prompt27
Iconnect Software28
Figure 4.2 Assigning an IP Address Using Iconnect28
Figure 4.3 Accessing the Wireless System for Configuration29
Setting a New IP Address over the Network30
Figure 4.4 Access Control30
Meter's Configurations and Operations31
Figure 4.5 Wireless System Home Page Menu31
Power up Meter32
Figure 4.6 LOGIN and ADMINISTRATOR Passwords32
Get Readings from the End Device33
Figure 4.7 Readings33
Figure 4.8 Comma Separated Value Format34
Java Runtime Environment Setup35
Java Runtime Environment 1.5 (5.0) Setup Instructions35
Figure 4.9 Java 1.5.X.X Screen Shots35
Java Runtime Environment 1.4 Setup Instructions36
Figure 4.10 Java 1.4 Screen Shots36
Browser Proxy Selection37
Java Policy38
Figure 4.11 Java Policy38
Figure 4.12 Java Policy39
Chart40
Figure 4.13 Chart40
Controller Setup42
Figure 4.14 Controller Setup42
Setup44
Input44
Figure 4.15 Input44
Setpoints & On/Off Control45
Figure 4.16 Setpoints & On/Off Control46
Alarms 1 & 248
Figure 4.17 Alarms 1 & 248
Analog Output Retransmission49
Figure 4.18 Analog Output Retransmission49
Display50
Figure 4.19A Display Menu50
Figure 4.19B Display Menu (if Analog Output Option)51
Display Color Examples52
Passcode ID54
Figure 4.20 ID Code54
Network Setup55
Figure 4.21 Network Setup55
End Device Setup57
Figure 4.22 End Device Setup57
End Device Parameters59
Figure 4.23 End Device Parameters59
Figure 4.24 Remote End Char60
Access Control61
Figure 4.25 Access Control61
Telnet Setup63
Httpget Program64
Httpget Using Port 200064
Httpget and ARP to Setup Device IP Address65
Figure 4.26 Httpget Example of Polling End Device65
Table 4.1 List of Commands65
Table 4.2 Connector/Transmitter Types65
ARP Protocol66
Figure 4.27 ARP Commands and Responses66
Ilog Software67
Figure 4.28 Ilog Software Logging Data for End Device67
Table 4.3 Ilog Excel Applications68
Mail Notifier Software69
Installation69
Figure 4.29 Mail Notifier Main Window69
Program Options Setup and Configuration70
Figure 4.30 Mail Notifier Profile Setup70
Device Settings and Configuration71
Table 4.4 Mail Notifier Commands71
Sending Txt Messages to a Cell Phone72
Figure 4.31 Mail Notifier Device Settings72
Part 5 Environment/Operating Conditions73
General Deployment Guidelines73
Figure 5.1 Operation in Buildings74
With Line-Of-Sight75
Figure 5.2 Fresnel Zone75
Without Line-Of-Sight76
Casing and Closure Around the Antenna76
Figure 5.3 Materials in Buildings76
Part 6 Specifications77
Part 7 Factory Preset Values80
Table 7.1 Factory Presets80
Appendix Aglossary84
Appendix Bip Address84
Appendix Cip Netmask86
Appendix Dascii Chart87
Appendix E Ilog Error Messages89
Appendix F Warning and Regulatory Information89

Newport wi Series - Display Color Examples

Table of Contents

Related product manuals