Nexa MLR-1923 User Manual

Power supply, doorbell 220–240 V ~50 Hz + 3 V CR2032
Protocol System Nexa (433.92 MHz)
Range up to 150 m
Memory slots 32
Ring tones 6
Volume levels High – Medium – Low – Silent
Operating temperature 0–40°C
IP classication IP20 doorbell
Dimensions, doorbell 100 x 59 x 37 mm
TECHNICAL DATA
Declaration of conformity published online at www.nexa.se
DELETING THE MEMORY, OTHER TRANSMITTERS
1. Press the programming button once; the LED indicator starts to
flash
2. Send the “ON” signal from the System Nexa Transmitter/Sensor
you wish to delete within 15 seconds; see the respective manual.
CONFIRMATION OF DELETION
The receiver beeps twice.
DELETION OF ALL MEMORY SLOTS
1. Press the programming button for 6 seconds, the LED indicator
starts to flash rapidly
2. Release the programming button and then press it briefly again.
CONFIRMATION OF DELETION, ALL MEMORY SLOTS
The doorbell beeps twice.
MEMORY
The MLR-1923 has 32 memory slots, which means it can be
controlled by up to 32 different transmitters at the same time.
• Plug-in doorbell for connection to a wall socket
• 6 dierent ring tones with the option of using dierent tones for
dierent push buttons/transmitters.
• 3 volume levels as well as silent.
• LED indicator that ashes for 15 seconds when the doorbell rings.
• Up to 32 push buttons/transmitters can be connect to one and the
same doorbell.
• An unlimited number of doorbells for one and the same push
button/transmitter.
• Functions with other System Nexa remote controls, motion
detectors and magnetic switches.
INSTALLATION
1. Connect the receiver to a wall socket
2. Press the volume control button to set the desired volume level;
choose between three different volume levels and silent. If you
choose the silent setting, only the LED indicator will flash when the
transmitter emits a signal. You can adjust the chosen volume level
at any time.
PROGRAMMING PUSH BUTTON
1. Programme the desired ring tone by pressing the ring tone button;
there are six different tones to choose from.
2. Press the programming button on the doorbell once, the LED
indicator starts to flash.
3. Press the push button for approx. 1 second.
PROGRAMMING, OTHER TRANSMITTERS AND SENSORS
1. Programme the desired ring tone by pressing the ring tone button;
there are six different tones to choose from.
2. Press the programming button on the doorbell once, the LED
indicator starts to flash.
3. Send the “ON” signal using a System Nexa Transmitter/Sensor
within 15 seconds; see the respective manual.
It is possible to link different ring tones to different push buttons/
transmitters. Repeat steps 1–3 from the programming procedure
described above for each push button/transmitter you want to
programme.
CONFIRMATION OF PROGRAMMING
The doorbell beeps twice.
DELETING THE MEMORY, PUSH BUTTON
1. Press the programming button once; the LED indicator starts to
flash
2. Press the push button you wish to delete within 15 seconds
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
info@nexa.se | www.nexa.se
MLR-1923
Doorbell (plug-in)
ENGLISH
SAFETY AND INFORMATION
Range: up to 150 m (optimal conditions). The range is heavily
dependent on local conditions – such as if there are any metals
nearby. For example, the heavy metal coating in low-emission
energy glass has a negative impact on the range of the radio
signals. There may be limitations on the use of the unit outside
the EU. If appropriate, check that the unit complies with the local
regulations.
Max. load: Never connect lights or equipment that exceeds the
maximum load of the receiver. This can result in faults, short circuit
or re.
Life support equipment : Never use Nexa products for life support
equipment or other devices where faults or disruptions can have
life-threatening consequences.
Disruptions: All wireless units can be aected by disruptions that
may have an impact on performance and range. The minimum
distance between two receivers should therefore be at least 50 cm.
Repairs: Do not attempt to repair the product. It does not contain
any serviceable parts.
Waterproofing: The product is not waterproof. Make sure that it is
always dry. Moisture will corrode the electronic components inside
and may result in short circuit, faults and risk of electric shock.
Cleaning: Clean the product with a dry cloth. Do not use chemicals,
solvents or potent cleaning agents.
Environment: Do not expose the product to extreme heat or cold,
as this may damage the electronic circuits or shorten their service
life.
Volume
Programming button
Ring tones

Nexa MLR-1923 Specifications

General

Brand	Nexa
Model	MLR-1923
Category	Accessories
Language	English