Nidec E300 Series - Page 141

Safety
information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
User Menu
A
Commissioning
Advanced
Parameters
Diagnostics Optimization CT MODBUS RTU Technical Data
Installation and System Design Guide 141
Issue Number: 1
A24
Symmetrical Current
Limit
{B16} ± VM_MOTOR1_CURRENT_LIMIT % 165.0 % 175.0 % RW Num RA US
A25
Maximum Switching
Frequency
{B13}
2 kHz (0), 3 kHz (1), 4 kHz (2), 6 kHz (3),
8 kHz (4) 12 kHz (5), 16 kHz (6)
8 kHz (4) RW Txt RA US
A26 Motor Autotune {B11}
None (0), Static (1),
Rotating (2)
None (0),
Static (1),
Rotating (2),
Inertia 1 (3),
Inertia 2 (4)
None (0),
Static (1),
Rotating (2),
Inertia 1 (3),
Inertia 2 (4), Full
Stationary (5)
None (0) RW Txt NC US
A27
Reverse Motor Phase
Sequence
{B26} Off (0) or On (1) 0ff (0) RW Bit US
A28
Nominal Elevator Speed
mm/s
{E01} 0 to 1000 mm/s 0 to 10000 1000 mm/s RW Num US
A29 Sheave Diameter {E02} 1 to 32,767 mm 400 mm 480 mm RW Num US
A30 Roping {E03} 1:1 (1), 2:1 (2), 3:1 (3), 4:1 (4) 1:1 (1) RW Txt US
A31 Gear Ratio Numerator {E04} 1 to 32767 31 1 RW Num US
A32 Gear Ratio Denominator {E05} 1 to 32767 1 RW Num US
A33
Nominal Elevator Speed
Rpm
{E07} 1.00 to 4000.00 rpm 1480.14 rpm 39.48 rpm RW Num US
A34
Motor Maximum
Frequency Clamp
{E08}
-214748364.8 to 214748364.7
54.8 Hz
RO Num US
Motor Maximum Speed
Clamp
{E08}
1644.6 rpm 43.8 rpm RO Num US
A35 Run Jerk 1 {G13}
1 to 65535 mm/s³ x10
50 mm/s³ x10 RW Num US
A36 Run Jerk 2 {G14} 1 to 65535 mm/s³ x10 100 mm/s³ x10 RW Num US
A37 Run Jerk 3 {G15} 1 to 65535 mm/s³ x10 100 mm/s³ x10 RW Num US
A38 Run Jerk 4 {G16} 1 to 65535 mm/s³ x10 50 mm/s³ x10 RW Num US
A39 Creep Stop Jerk {G18} 1 to 65535 mm/s³ x10 100 mm/s³ x10 RW Num US
A40 Acceleration Rate {G11} 0 to 10000 mm/s² 800 mm/s² RW Num US
A41 Deceleration Rate {G12} 0 to 10000 mm/s² 500 mm/s² RW Num US
A42
Creep Stop Deceleration
Rate
{G17} 0 to 10000 mm/s² 1000 mm/s² RW Num US
A43 V1 Speed Reference {G01}0 to Nominal Elevator Speed (A28)50 mm/sRWNumUS
A44 V2 Speed Reference {G02}0 to Nominal Elevator Speed (A28) 400 mm/s RW Num US
A45 V3 Speed Reference {G03}0 to Nominal Elevator Speed (A28) 600 mm/s RW Num US
A46 V4 Speed Reference {G04}0 to Nominal Elevator Speed (A28)10 mm/sRWNumUS
A47
Brake Control Release
Delay
{D04} 0 to 10000 ms 500 ms RW Num US
A48
Brake Control Apply
Delay
{D05} 0 to 10000 ms 500 ms RW Num US
A49 Start Speed Loop P Gain {I01}
0.0000 to 200.0000 s/rad 1.0000 s/rad RW Num US
A50 Start Speed Loop I Gain {I02}
0.00 to 655.35 s
2
/rad 20.00 s
2
/rad
RW Num US
A51 Start Current Loop Filter {I05}
0.0 to 25.0 ms 2.0 ms RW Num US
A52 Run Speed Loop P Gain {I06}
0.0000 to 200.0000 s/rad 0.5000 s/rad RW Num US
A53 Run Speed Loop I Gain {I07}
0.00 to 655.35 s
2
/rad 10.00 s
2
/rad
RW Num US
A54 Run Current Loop Filter {I10}
0.0 to 25.0 ms 2.0 ms RW Num US
A55 Start Lock Enable {I22}
Off (0) or On (1) Off (0) RW Bit US
A56
Start Lock P Gain Speed
Clamp
{I21}
0 to 10000 mm/s 40 mm/s RW Num US
A57 Start Lock P Gain {I20}
0.000 to 1000.000 20.000 RW Num US
A58 Start Optimizer Time {G48}
0 to 10000 ms 500 ms RW Num US
A59 Start Optimizer Jerk {G47}
±VM_EX00_RUN_JERK_
1 mm/s
3
x 10
10 mm/s
3
x 10
RW Num US
A60 Start Optimizer Speed {G46} 0 to 10000 mm/s 50 mm/s 10 mm/s RW Num US
A61 Start Optimizer Enable {G45}
Off (0) or On (1) Off (0) RW Bit US
A62
to
A80
User Menu A
Parameters Set-up
Using Menu Z
RW Read / Write RO Read only Num Number parameter Bit Bit parameter Txt Text string Bin Binary parameter FI Filtered
ND No default value NC Not copied PT Protected parameter RA Rating dependent US User save PS Power-down save DE Destination
IP IP address Mac Mac address Date Date parameter Time Time parameter
Parameter
Range(Ú) Default(Ö)
Type
OL RFC-A RFC-S OL RFC-A RFC-S