EasyManuals Logo

Nissan Armada Quick Reference Guide

Nissan Armada
13 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
01
To adjust the seatback, pull up on the lever and lean back. This allows adjustment of
the seatback for occupants of different sizes to help obtain proper seat belt fit.
01
To fold the 2nd row captain’s chair (if so equipped) flat for maximum cargo hauling:
Remove the 2nd row center console (see “Console removal” in the “Instruments and
controls” section of the Owner’s Manual).
Pull the strap located in the center of the seat cushion forward, and fold the seat
cushion toward the front of the vehicle.
02
Then lift up on the recline lever to fold the seatback flat forward.
01
Then fold the carpet panel flap toward the back of the vehicle. (The carpet panel flaps
provide a level cargo floor when the 3rd row seats are also folded flat.)
03
Reverse this process to return the 2nd row captain’s chair to a seating position.
Make sure to properly raise the seatback to an upright position and push the seat
cushion down into place.
ADJUSTING AND FOLDING THE 2ND ROW SEAT
02
03
TIP UP FOR EASY ENTRY TO THE 3RD ROW
 The 2nd row outboard seats can be tipped forward for easy entry or exit from the
3rd row bench seat. To enter the 3rd row, lift up on the latch located on the upper
corner of the seatback on the 2nd row outboard seats and fold the seatback
forward at an angle at the seat base. This will release the back of the seat so it
may be tipped forward.
01
Then lift up on the lower corner of the seat base and tip the 2nd row outboard
seat forward. To exit the 3rd row bench seat, lift up on the same latch and fold the
seatback forward onto the seat base. Then, lift up on the seat base and tip it forward.
01
FOLDING THE 3RD ROW SPLIT BENCH SEAT
 To fold the seats flat, disconnect and secure the
center seat belt and tongues from the retractor
base. Then pull up on the latch
01
located on the
outside corner of each seatback and fold the
seatback forward over the seat base.
 To raise the seats, lift the seatbacks and make sure
they are fully latched in the upright position.
01 01
DRIVER FRONT SEAT ADJUSTMENTS
With manual seats (passenger’s side,
if so equipped):
Pull up on the lever under the front of the seat and
slide backward or forward; release.
Lift the lever on the side of the seat to adjust your
seatback backward or forward; release when you
have found a comfortable angle and the seat belt
fits properly.
01
With power seats (if so equipped):
Move the control forward or backward to adjust the
seat cushion forward or backward.
02
Pull up to raise the seat cushion; press down to lower
the cushion.
02
Push the switch forward to move the seatback forward;
push it back to move the seatback backward.
03
Your driver’s seat has a lumbar support; adjust it by
AUTOMATIC CLIMATE CONTROL
10
SEEK/TRACK BUTTON
To scan quickly through each broadcasting station, press the
SEEK/TRACK button.
To skip from one track to another on a CD, press the SEEK/TRACK button.
Each time the button is pressed, the CD will advance or skip back one track.
CAT FOLDER BUTTON
To manually tune the radio, press the CAT FOLDER button. If playing a CD that is
formatted with MP3 folders, press the CAT FOLDER button to scroll through the
folder.
PRESET A
.
B
.
C BUTTON
Press the PRESET A
.
B
.
C button to change between the preset storage banks.
The radio displays the icon A, B, or C to indicate which preset bank is active. Each
memory bank can hold any combination of AM, FM, and SAT* presets.
REAR ON
.
OFF
To turn rear audio controls on, press the REAR ON
.
OFF button. Press again to turn
the rear controller off. To turn on the DVD mode (if so equipped), press and hold the
REAR ON
.
OFF button for 2 seconds.
SPEAKER CONTROL BUTTON
Press this button to turn the rear speakers off and headphones on. Press this button
again to turn the rear seat speakers back on and headphones off.
LOAD BUTTON
LOAD A SINGLE DISC
Press the LOAD button for less than 1.5 seconds. Select the loading slot by
pressing the CD SELECT button (1 to 6), then insert the CD.
LOAD UP TO 6 DISCS
Press the LOAD button for more than 1.5 seconds.
STATION AND CD SELECT BUTTONS
To store a radio station in a preset, you must first select the A, B, or C memory
bank by pressing the PRESET A
.
B
.
C button and tuning to the desired AM, FM or
SAT* station. Then, press the desired station select button for at least 2 seconds.
When the preset indicator illuminates, a beep will sound, indicating memorization
is complete. To retrieve a previously set station, select the memory bank where the
preset was set, then press the corresponding station select button.
FM/AM SAT* RADIO WITH 6 DISC IN-DASH CD CHANGER (if so equipped)
11
* SAT presets are only available on SAT equipped vehicles.
05
04
03
02
01
07
06
01
02
03
04
05
06
07
01
NISSAN ARMADA ADDITIONAL FEATURES (continued)
TEMPERATURE CONTROL DIALS
Turn the driver temperature control dial to set the desired temperature. If
the passenger temperature control is not turned, the driver’s temperature
selection will control air for the driver and passenger.
If the passenger temperature control dial is turned, the passenger’s
temperature will be controlled independently from the driver’s.
FAN SPEED CONTROL DIAL
The fan speed control button turns the fan on and off, and controls the fan speed.
DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the FRONT WINDOW DEFROSTER button on.
Turn the TEMPERATURE dial left or right to set the desired temperature.
Make sure the AIR RECIRCULATION button is off to allow fresh air to
be drawn into the vehicle. To set the defroster on high, turn the fan control dial
to set the fan speed to maximum.
DEFROSTING/DEFOGGING REAR WINDOW AND OUTSIDE HEATED
MIRROR (if so equipped)
Push the REAR WINDOW DEFROSTER switch on. Push the switch
again to manually turn the defroster off. NOTE: The rear window defroster
automatically turns off in approximately 15 minutes.
AIR FLOW MODE CONTROL BUTTON
The air flow mode control button allows you to select the air flow outlets.
Air flows from the center and side vents.
Air flows from the center, side, and foot vents.
Air flows mainly from the foot vents.
Air flows from the defroster and foot vents.
Air flows mainly from the defroster vents.
A/C ON/OFF BUTTON
Start the engine, turn the FAN SPEED CONTROL dial to the desired position and
press the A/C button to turn on the air conditioner. Press the A/C button again to
turn off the air conditioner.
AIR RECIRCULATION BUTTON
Press the AIR RECIRCULATION button to recirculate air inside
the vehicle.
Press the AIR RECIRCULATION button again to turn air
recirculation off.
Air recirculation mode cannot be selected if the air flow control dial is in the
defrost position.
05
04
03
02
01
06
07
02
03
04
05
06
01
07
LOCK/UNLOCK DOORS
Press the UNLOCK button once to unlock the
driver’s door.
Press the UNLOCK button twice within 5 seconds to
unlock all doors.
Make sure all doors and windows are closed and
press the LOCK button to secure the vehicle.
OPEN WINDOWS
Press the UNLOCK button longer than 3 seconds to open
the front windows. (The keyfob is not able to close the windows after opening them.)
POWER LIFT GATE (if so equipped)
Press and hold the power lift gate button for longer than 0.5 seconds to open
or close the power lift gate. The hazard lights will flash and a chime will sound
to indicate that the power open or power close sequence has started. If you press
the button again, the lift gate will reverse direction immediately; a chime will sound to
indicate the reversal.
CHILD SAFETY DOOR LOCK
You’ll find the safety lock levers on the edge of the rear doors.
When in the LOCK position, the rear door can only be opened from
the outside.
REAR SONAR SYSTEM OFF SWITCH
When backing up, this system will beep to alert you to obstacles
within 6 ft. of the rear bumper. The system beeps faster as the
vehicle gets closer to the obstacle. A continuous tone sounds
when an obstacle is less than 10 inches away from the bumper.
Turn the system off by pushing the REAR SONAR SYSTEM OFF
switch. Push the switch again to enable the system. The system will
automatically reset the next time the ignition switch is turned on.
ADJUSTABLE ACCELERATOR AND BRAKE
PEDALS (if so equipped)
The accelerator and brake pedals can be adjusted for your
driving comfort.
Adjust the pedals when the automatic transmission lever is
in P (Park).
To move the position of the pedals forward, push
.
01
To move the position of the pedals backward, push
.
02
POWER LIFT GATE (if so equipped)
To operate the power lift gate, the automatic transmission lever must
be in P (Park).
Power Open
 The lift gate can be opened by the button on the keyfob,
the instrument panel switch and by the outside opener handle.
 The lift gate must be unlocked to open it with the outside opener
handle.
Power Close
 The power close feature can be activated by the button on
the keyfob, the instrument panel switch and the rear pillar switch.
 The keyfob button must be held for 0.5 seconds before the
lift gate closes.
Cancel Switch
 The switch on the rear pillar cannot be used to open the lift gate. Pushing the
switch toward the CANCEL position will disable the rear pillar switch.
 The lift gate can still be opened and closed using the switch on the instrument
panel and the keyfob button.
 The lift gate can also be opened manually with the outside handle if the lift gate
is unlocked.
04
03
02
01
01
02
REMOTE KEYLESS ENTRY SYSTEM
Shift_scale
2006 ARMADA
QU ICK R EFER ENCE GU IDE
AUTOMATIC DRIVER POSITIONER (if so equipped)
The automatic driver positioner system has two features:
 Memory storage function.
Entry/exit function.
MEMORY STORAGE FUNCTION
Two positions for the driver’s seat, accelerator and brake
pedals, and outside mirrors can be stored in the automatic
driver positioner memory. Follow these procedures to set
driver preferences.
SET THE DESIRED POSITIONING
1. Set the automatic transmission lever to the P (Park) position.
2. Turn the ignition on and adjust the driver’s seat, accelerator and brake pedals, and
outside mirrors to the desired positions.
3. Press the
SET (memory) button and within 5 seconds press the position button
(1 or 2) for at least 1 second until the indicator light illuminates. The position is now
stored in memory.
LINK TO KEYFOB
Within 5 seconds of setting the memory position (indicator light is on and ignition is
on), press the
button on the remote.
A keyfob can be linked to each memory button.
If memory positioning is re-set to a new location, it will be necessary to re-link
the keyfob.
RECALLING A MEMORY SETTING FROM THE MEMORY PAD
Set the automatic transmission lever to the P (Park) position, then:
Within 45 seconds of opening the driver’s door, push the memory switch (1 or 2) fully
for at least 1 second, or
Turn the ignition switch to the ON position and push the memory switch (1 or 2) fully for
at least 1 second.
FROM THE KEYFOB
If properly linked, operation of the button will automatically return the driver’s seat,
accelerator and brake pedals, and outside mirrors to the memorized position.
ENTRY/EXIT FUNCTION
The driver’s seat automatically moves to allow the driver to get into and out of the driver’s
seat more easily. The driver’s seat slides backward when:
The driver’s door is opened with the key turned to LOCK.
The key is turned from ACC to LOCK with the driver’s door open and the automatic
transmission lever is in the P (Park) position.
The driver’s seat returns to the previous position when:
The key is inserted into the ignition switch.
The driver’s door is closed with the key turned to LOCK.
 The key is turned from ACC to ON while the automatic transmission lever is in the
P (Park) position.

Other manuals for Nissan Armada

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Nissan Armada and is the answer not in the manual?

Nissan Armada Specifications

General IconGeneral
BrandNissan
ModelArmada
CategoryAutomobile
LanguageEnglish

Related product manuals