Hearing aids
Some digital wireless devices may interfere with some
hearing aids.
Vehicles
RF signals may affect improperly installed or
inadequately shielded electronic systems in motor
vehicles such as electronic fuel injection, electronic
antilock braking, electronic speed control, and air bag
systems. For more information, check with the
manufacturer of your vehicle or its equipment.
Only qualified personnel should service the device or
install the device in a vehicle. Faulty installation or
service may be dangerous and may invalidate your
warranty. Check regularly that all wireless device
equipment in your vehicle is mounted and operating
properly. Do not store or carry flammable liquids, gases,
or explosive materials in the same compartment as the
device, its parts, or accessories. Remember that air bags
inflate with great force. Do not place your device or
accessories in the air bag deployment area.
Switch off your device before boarding an aircraft. The
use of wireless teledevices in an aircraft may be
dangerous to the operation of the aircraft and may be
illegal.
Potentially explosive environments
Switch off your device in any area with a potentially
explosive atmosphere. Obey all posted instructions.
Sparks in such areas could cause an explosion or fire
resulting in bodily injury or death. Switch off the device
at refuelling points such as near gas pumps at service
stations. Observe restrictions in fuel depots, storage, and
distribution areas; chemical plants; or where blasting
operations are in progress. Areas with a potentially
explosive atmosphere are often, but not always, clearly
marked. They include areas where you would be advised
to turn off your vehicle engine, below deck on boats,
chemical transfer or storage facilities and where the air
contains chemicals or particles such as grain, dust, or
metal powders. You should check with the
manufacturers of vehicles using liquefied petroleum gas
(such as propane or butane) to determine if this device
can be safely used in their vicinity.
Emergency calls
Important: This device operates using radio signals,
wireless networks, landline networks, and user-
programmed functions. If your device supports voice
calls over the internet (internet calls), activate both the
internet calls and the cellular phone. The device may
attempt to make emergency calls over both the cellular
networks and through your internet call provider if both
are activated. Connections in all conditions cannot be
guaranteed. You should never rely solely on any wireless
device for essential communications like medical
emergencies.
To make an emergency call:
1 If the device is not on, switch it on. Check for
adequate signal strength. Depending on your
device, you may also need to complete the
following:
• Insert a SIM card if your device uses one.
• Remove certain call restrictions you have
activated in your device.
• Change your profile from Offline or Flight
profile to an active profile.
2 Press the end key as many times as needed to clear
the display and ready the device for calls.
3 Enter the official emergency number for your
present location. Emergency numbers vary by
location.
4Press the call key.
When making an emergency call, give all the necessary
information as accurately as possible. Your wireless
device may be the only means of communication at the
scene of an accident. Do not end the call until given
permission to do so.
Certification information (SAR)
This mobile device meets guidelines for exposure to
radio waves.
Your mobile device is a radio transmitter and receiver. It
is designed not to exceed the limits for exposure to radio
waves recommended by international guidelines. These
guidelines were developed by the independent scientific
organisation ICNIRP and include safety margins
designed to assure the protection of all persons,
regardless of age and health.
The exposure guidelines for mobile devices employ a
unit of measurement known as the Specific Absorption
Rate or SAR. The SAR limit stated in the ICNIRP guidelines
is 2.0 watts/kilogram (W/kg) averaged over 10 grams of
tissue. Tests for SAR are conducted using standard
operating positions with the device transmitting at its
highest certified power level in all tested frequency
bands. The actual SAR level of an operating device can
be below the maximum value because the device is
designed to use only the power required to reach the
network. That amount changes depending on a number
of factors such as how close you are to a network base
station.
Product and safety information 57
www.nokia.com/support
Cyan
Magenta
Yellow
Black
2010 Nokia. All rights reserved.
©
To Next Page
Loading...
