Nord Drivesystems SK 510P - Electrical Connection; Wiring Guidelines; Mains Connection

3 Assembly and installation
BU 0630 en-2020 29
Remove the control
terminals and blank
cover.
Remove the STO
contact jumper.
Install the SK CU5-STO
customer unit.
Install the control
terminals and blank
cover.
Pos: 12 6 /Anlei tu nge n/El ektr onik /S afety /4 . M ontag e u nd I nst all ati on/ Elek tri sch er Ans chl uss _0 1 @ 15\mod_1485429904375_388.docx @ 2316246 @ 2 @ 1
3.2 Electrical connection
The information for installation or electrical connection from the manual BU 0600 as well as all of the
following information must be observed.
Pos: 12 7 /Anlei tung en/El ektr onik/FU und Star ter/1 . Allg emei nes/Sic herh eits- und Ins tall ations hinwei se un d Warn- G efa hren hinw eise /Sic her heit shi nwei se (a usla ufe nd)/ vers chie den e/W ARNU NG - Elek tris cher Sc hlag ( nich t un ter Spa nnu ng ar bei te n) @ 14\m od_1480331381423_388.docx @ 2308485 @ @ 1
WARNING
Electric shock
Touching electrically conducting components may cause an electric shock and severe or possibly fatal injury.
• Disconnect the frequency inverter from the power supply before starting installation work.
• Only work on devices which have been disconnected from the power supply.
Pos: 12 8 /Anlei tung en/El ektr onik/FU und Star ter/1 . Allg emei nes /Sic herh eits - und I nstall atio nshinw eise un d Warn- Gefa hre nhi nw eise /Sic her hei tshi nw eise (a usla ufe nd)/ vers chi ed ene/W AR NUN G - El ektri scher Schlag (Wartez eit) @ 14\mod_1480332099956_388.docx @ 2308520 @ @ 1
WARNING
Electric shock
The frequency inverter carries hazardous voltage for up to 5 minutes after being switched off.
• Only start work after a waiting period of at least 5 minutes after switching off the mains supply
(disconnection).
Pos: 13 0 /Anlei tung en/El ektr onik/S afety /4. Mon tage u nd I nst all ati on/ Ver draht ung sri chtl ini en [ BU0 630] @ 44\mod_1593153830132_388.docx @ 2638326 @ 3 @ 1
3.2.1 Wiring guidelines
Wire end sleeves must be used if flexible cables (multiple strand or fine-wire) are used for the
connections X19 (at position X17) or X20. In addition, the wiring guidelines in the frequency inverter
manual (BU 0600) also apply.
Pos: 132 /A nleit ung en/El ek tr onik /Saf ety /4. M on tage un d I nstal la tio n/Net za nschl uss [B U0 630] @ 4 0\mod_1578408046098_388.docx @ 2582167 @ 3 @ 1
3.2.2 Mains connection
Devices for implementation of a safety function must only be operated on TN, TT and IT networks.
Grounded Corner operation is not intended.
For operation in IT networks
• the IT network screws must be removed
• a braking resistor must be used
Pos: 13 3 /Anlei tung en/El ektr onik/FU und Star ter/1 . Allg emei nes/Sic herh eits- und Ins tall ations hinwei se un d Warn- Gefahrenhinweise/neu/Warn- und Ge fahr enhinw eise /ACHTU NG - Be tri eb am IT – Netz [ SK 5xxP] @ 32\mod_1553605071546_388.docx @ 2520590 @ @ 1