Nortek 2GIG eSeries GC2e - Key Fob Programming; Q3: RF Key Fob Programming Outline; RF Key Fob Programming Questions

Q1: SELECT FOB #
PRESS TO FINISH PROGRAMMING SENSOR
THEN PRESS TO PROGRAM THE NEXT SENSOR
OR PRESS TO JUMP TO Q2: WIRED SENSOR PROGRAMMING
Q: SELECT FOB # USED
Q: SELECT FOB # EQUIPMENT
CODE
Q: ENTER FOB # OTHER
EQUIPMENT CODE
(Only appears if (0000) Other
was selected in previous queston)
Q: ENTER FOB # SERIAL NUMBER
Q: SELECT FOB # EQUIPMENT AGE
Q: SELECT FOB # EMERGENCY KEY
Q: SELECT KEY FOB # KEY 2
CAN DISARM
Q: CONSTRUCT FOB #
VOICE DESCRIPTOR
Q: SELECT FOB # ARM NO DELAY
Q: SELECT FOB # KEY 4 OUTPUT
Q3: RF Key Fob Programming Outline
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD
PRESS FOR NEXT OPTION
shift
ENTER ON KEYPAD OR PRESS
OR
THEN SEND SIGNAL
FROM KEY FOB
learn
PRESS FOR EACH WORD
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
shift
edit next
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
PRESS FOR NEXT OPTION
skip
GC2e Wireless Security System | Installation and Programming Guide
©2020 Nortek Security & Control LLC. All rights reserved. 45 2GIG is a registered trademark of Nortek Security & Control LLC.
Key Fob Programming Outline
Q3: RF Key Fob Programming Outline
Figure 49 Key Fob Programming Outline
Summary of RF Key Fob # Screen
Aer seng all the opons for a key fob, the Summary of Fob # screen
is displayed. The screen can also be displayed for programmed keyfobs
during keyfob program eding by tapping the Sum buon.
• While programming each key fob remember that the ← and →
arrow bu ons step through each of the key fob numbers.
• To return to programming, tap the Edit Current or Edit Next buons.
• Tapping Skip goes to queson number Q4 (RF Keypad Programming).
See “Wireless (RF) Keypad Programming” on page 46.
RF Key Fob Programming Questions
Q3: Select Fob # (1 to 8)
Up to eight (8) wireless four (4)-buon key fobs can be used with each
Control Panel. Key fobs reports as sensors 51-58. The opons for each fob
are programmed with sub-opon quesons.
• Begin by entering the fob number or select it using the ← or →
arrows.
• Program the key fobs by using ↑ and ↓ arrows to select the sub-
opons.
NOTE: To skip RF key fob programming, tap Skip to jump from
queson Q3 to queson Q4 (RF keypad programming). See “RF Keypad
Programming Quesons” on page 47.
Q: Select Fob # Used (0 to 1)
DEFAULT: (0) Unused
Key fobs can be used with the Control Panel or not.
• The default seng (0) Unused sets all key fobs as unused.
• To en able programming for this key fob, select (1) Used.
Q: Select Key Fob # Equipment Code (0-9999)
DEFAULT: (0000) Other
The key fob equipment code denes the sensor’s manufacturer and type.
• The default seng is (0000) Other.
• Select (0866) 2GIG 4‐buon Key Fob remote for a 2GIG-KEY2 key
fob remote.
• Select (0577) Exisng Key Fob for an exisng key fob remote.
NOTES:
• Only 2GIG 4-Buon Key Fob Remotes are compable with this
system.
• When programming eSensors (Wireless & Keyfobs) the equipment
code must match the sensor being installed.
Q: Enter Key Fob # Other Equipment Code (0-9999)
DEFAULT: 0
NOTE: This queson is only displayed if (0000) Other is selected for a key
fob’s equipment code.
• The equipment code is a four (4)-digit code that is assigned to the
model of key fob being used.
• Enter the equipment code number for the key fob.
Scroll between op ons using the ← and → arrows. Move to
the previous or next prompt by tapping the ↑ and ↓ arrows.
1. To program another sensor tap Next.
2. To exit programming, tap Skip, then End, and then Exit.
Upon exit, the panel takes several seconds to restart.
3. TIP: Tap Skip to jump to queson Q4. See “RF Keypad
Programming Quesons” on page 47.
Installer Programming