EasyManuals Logo

NOVAK GTB - PROFILE SELECTION & GEARING GUIDE User Manual

NOVAK GTB - PROFILE SELECTION & GEARING GUIDE
2 pages
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
Throttle Profiles 1, 2, 3, 4, & 6 can be independently customized
to
fine tune the speed control to feel just the way you like it.
The GTB lets you adjust the following software parameters:
Minimum Brake/Drag Brake Percentage--1 of 10 settings.
Braking Type--1 of 2 types of braking styles (standard Constant Force braking
or DRAG BRAKING where braking is applied during neutral).
Dead Band--1 of 5 Dead Band settings from 2 to 6%
.
Drive Frequency (Profile 6 only)--
1 of 7 Drive Frequencies from 1.5 to 11kHz.
Minimum Drive Percentage--1 of 5 settings from 2 to 12%
.
gtb soFtware Flow chartgtb soFtware Flow chart
gtb soFtware Flow chartgtb soFtware Flow chart
gtb soFtware Flow chart
::
::
:
❊❍❊❘GI❍
✑✑
✬✾✼✽✸✶✄ ❚❙❑❊◗◗M✷✰
PLEASE NOTE: This page contains optional Advanced Programming items!
No further adjustments are required.
(but don’t worry, you can always reset factory defaults by performing the One-Touch programming again, so go ahead & experiment--that’s why the programming is in there, right?)
P6
to customizing profiles to customizing profiles
to customizing profiles to customizing profiles
to customizing profiles
11
11
1
--
--
-
44
44
4
or or
or or
or
66
66
6
::
::
:
With ESC on & connected to a charged battery
(transmitter ON or OFF)
:
1. IF TRANSMITTER IS OFF, DISCONNECT ESC FROM RECEIVER
Remove input signal harness from receiver to avoid radio interference.
2. MAKE SURE THROTTLE PROFILE 1-4 OR 6 IS ACTIVE
If you are not sure what profile is selected, follow the procedures in ‘Throttle
Profile Selection’ to check or select desired profile.
Remember that you can not access the Brush-Mode
(Profile #6)
without
disconnecting the brushless motor’s sensor harness from the ESC.
Note: there is no time constraint during selection process of custom parameters.
to adjust minimum braketo adjust minimum brake
to adjust minimum braketo adjust minimum brake
to adjust minimum brake
::
::
:
(or re-activate std-style brakes)
aa
aa
a
..
..
. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until the Blue status LED
turns on solid---Release ESC’s SET button once LED is on solid.
bb
bb
b
..
..
. SELECT MINIMUM BRAKE PERCENTAGE
blue
Blue status LED (1st LED on left) flashes to indicate active Minimum Brake
setting. Quick press & release to select desired setting.
cc
cc
c
..
..
. PRESS & HOLD SET BUTTON TO STORE SELECTION
When SET button is pressed & held for about 1 second, the new selection is
stored in ESC’s memory--The 4 status LEDs will scroll back & forth to indicate
you are exiting programming & the Red LED will turn on solid (Red & Green if no
transmitter signal present)--ESC is at neutral & ready to go.
to activate & adjust drag braketo activate & adjust drag brake
to activate & adjust drag braketo activate & adjust drag brake
to activate & adjust drag brake
::
::
:
aa
aa
a
..
..
. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until Blue & Amber status
LEDs turn on solid---Release SET button once LEDs are solid.
bb
bb
b
..
..
. SELECT DRAG BRAKE PERCENTAGE
blue & amber
Blue & Amber status LEDs (1st & 2nd LEDs on left) flash to indicate active
Drag Brake setting (Drag brake setting will be same as Minimum Brake setting).
Quick press & release to change Drag Brake/Minimum Brake setting, then
press & hold SET button for about 1 second to activate drag braking, store
selection into ESC’s memory, and return to neutral.
Note: To re-activate the standard style of braking
(no drag brakes during
neutral)
, repeat Minimum Brake adjustment as described above.
to adjust dead bandto adjust dead band
to adjust dead bandto adjust dead band
to adjust dead band
::
::
:
aa
aa
a
..
..
. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until Blue & Green status
LEDs turn on solid---Release SET button once LEDs are solid.
bb
bb
b
..
..
. SELECT DEAD BAND PERCENTAGE
blue & green
Blue & Green status LEDs flash to indicate active Dead Band setting. Quick
press & release to change setting, then press & hold SET button for about 1
second to store selection and return to neutral.
to adjust minimum driveto adjust minimum drive
to adjust minimum driveto adjust minimum drive
to adjust minimum drive
::
::
:
aa
aa
a
..
..
. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until Amber status LED turns
on solid---Release SET button once LED is on solid.
bb
bb
b
..
..
. SELECT MINIMUM DRIVE PERCENTAGE
amber
Amber status LED flashes to indicate active Minimum Drive setting. Quick
press & release to change setting, then press & hold SET button for about 1
second to store selection and return to neutral.
to adjust drive frequencyto adjust drive frequency
to adjust drive frequencyto adjust drive frequency
to adjust drive frequency
::
::
:
(Profile 6 ONLY)
aa
aa
a
..
..
. PRESS & HOLD SPEED CONTROL’S SET BUTTON
With ESC at neutral, press & hold SET button until Green status LED turns
on solid---Release SET button once LED is on solid.
bb
bb
b
..
..
. SELECT DRIVE FREQUENCY
green
Green status LED flashes to indicate active Drive Frequency setting. Quick
press & release to change setting, then press & hold SET button for about 1
second to store selection and return to neutral.
restoring factory defaultrestoring factory default
restoring factory defaultrestoring factory default
restoring factory default
ss
ss
s
::
::
:
Every time you perform the One-Touch Set-Up, the factory default settings are
restored for each of the throttle profiles.
@NEUTRAL
RED or RED & GREEN
MIN. BRAKE
BLUE
DRAG BRAKE
BLUE & AMBER
ACTIVE PROFILE
all LEDs (flashing)
DEAD BAND
BLUE & GREEN
MIN. DRIVE
AMBER
press & hold
press & hold
press & hold
press & hold
press & hold
continue holding ESC’s SET button to skip steps here
LEDs roll off
––––
exit programming
Setting
(# of flashes)
:
12345678910
Minimum Brake
(%)
: 5 101520253035404550
Setting
(# of flashes)
:
12345678910
Drag Brake
(%)
:off10 15 20 25 30 35 40 45 50
Setting
(# of flashes)
:
12345
Dead Band
(%)
: 23456
Setting
(# of flashes)
:
12345
Minimum Drive
(%)
: 235812
if Brush-Mode
is active
––––––
all LEDs
flash 6 times
@NEUTRAL
RED or RED & GREEN
if Brushless-Mode
is active
––––––
# of flashes equals
active profile (
1-5
)
if pressed
––––––
within 3 sec. of
all LEDs flashing
––––––
active profile
changed
if not pressed
––––––
within 3 sec. of
all LEDs flashing
Setting
(# of flashes)
:
1234567
Drive Frequency
(kHz)
: 1.5 2.5 3.5 4.5 6.5 8.5 11
DRIVE FREQUENCY
GREEN
press & hold
if Brush-Mode
is active
if Brushless-Mode
is active

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NOVAK GTB - PROFILE SELECTION & GEARING GUIDE and is the answer not in the manual?

NOVAK GTB - PROFILE SELECTION & GEARING GUIDE Specifications

General IconGeneral
BrandNOVAK
ModelGTB - PROFILE SELECTION & GEARING GUIDE
CategoryController
LanguageEnglish

Related product manuals