36
RE3: Input 2 Gain
Displayed as: In2Gain
Default value: Off
Range of adjustment: -10 to +65
Adjusts input gain for Input 2 with Input Linking (RE1) set to Indept and for both Inputs 1
and 2 with Input Linking set to Stereo. Operation is otherwise identical to RE2.
RE4 to RE6: Not used.
RE7: Input 1 FX Send
Displayed as: In1~Fx
Default value: 0
Range of adjustment: 0 to 127
This parameter adjusts the amount of Input 1’s signal sent to the FX processor for the cur-
rently selected Patch. If Input Linking is set to Stereo, it simultaneously adjusts the FX
send level for both Input 1 and Input 2.
Try scrolling through the factory Patches to experiment with the different FX
which they contain to see how different FX alter your input signal. Alternatively,
try one of the Patches in the ExtInput category.
RE8: Input 2 FX Send
Displayed as: In2~Fx
Default value: 0
Range of adjustment: 0 to 127
This parameter adjusts the amount of Input 2’s signal sent for FX processing. If
Input Linking is set to Stereo, it simultaneously adjusts the FX send level for both Input 1
and Input 2.
Audio Menu Page 2 – Headphones
RE1: Headphone level control select
Displayed as: HeadPhones Level Control
Default value: Follow master volume (1+2 only)
Range of adjustment: Follow master volume (1+2 only) or
Use Level and Balance 1+2/3+4
With Follow master volume (1+2 only) selected, the level of the signal at the stereo
headphone socket [8] will be adjusted by the Master Volume control [29]. The Head-
phone volume (RE6) and Headphone balance (RE7) controls will be inoperative. What
you hear in the headphones will be the same mix and balance as that being fed to Outputs
1 and 2. With Use Level and Balance 1+2/3+4 selected, the Headphone volume and
source blend may be adjusted independently by RE6 and RE7.
RE2 to RE5: Not used.
RE6: Headphone volume
Displayed as: Level
Default value: 127
Range of adjustment: 0 to 127
This adjusts the headphone volume, when Use Level and Balance 1+2/3+4 is selected
by RE1.
RE7: Headphone balance
Displayed as: Balance
Default value: 0
Range of adjustment: -64 to +63
When Use Level and Balance 1+2/3+4 is selected by RE1, the audio at the head-
phones socket is a mix of the signal at Outputs 1 and 2 (a stereo pair) and that at Outputs
3 and 4 (another stereo pair). Refer to the following menu pages for details on how to set
up Outputs 1 & 2 and 3 & 4.
RE8: Not used.
Audio Menu Page 3 – Outputs 1 and 2, and Host source
Outputs 1 & 2 may carry a mix of synth sounds, the audio sources connected at Inputs 1
and/or 2, and DAW channels 1 & 2. The default setting for the Output 1+2 mix is synth
sound at full level and no external audio, apart from any routed to the FX processor. The
MONITOR control [28] on the top panel provides a balance between DAW channels 1 & 2
and the mix of synth sound and audio inputs set up with RE3, RE4 and RE5.
The USB port can additionally send a further mix directly to a computer.
RE1: Not used, but LCD confirms that this page is concerned with Outputs 1 & 2.
RE2: Synth level
Displayed as: Synth
Default value: 127
Range of adjustment: 0 to 127
RE2 adjusts the level of sounds generated by the synthesiser present in the mix at Outputs
1 and 2.
RE3: Input 1 level
Displayed as: Input1
Default value: 0
Range of adjustment: 0 to 127
Audio from Input 1 may be mixed into Outputs 1 and 2 by adjusting RE3. With Input Link-
ing (RE1 on Audio Menu Page 1) set to Indept, RE3 adjusts level for Input 1 only. With
Input Linking set to Stereo, the level of both Inputs 1 and 2 will be adjusted as a pair.
RE4: Input 2 level
Displayed as: Input2
Default value: 0
Range of adjustment: 0 to 127
Audio from Input 2 may be mixed into Outputs 1 and 2 by adjusting RE4. With Input Link-
ing (RE1 on Audio Menu Page 1) set to Indept, RE4 adjusts level for Input 2 only. With
Input Linking set to Stereo, the level of both Inputs 1 and 2 will be adjusted as a pair.
RE5 and RE6: Not used.
RE7: Record Mode
Displayed as: RECORD Mode
Default value: Synth
Range of adjustment: Synth, Inputs, Synth+Inputs
In addition to the analogue outputs 1 to 4 and the S/PDIF digital audio output, a further
digital audio output is available via the UltraNova’s USB port. This allows synth sounds
and/or audio inputs to be sent via USB direct to your computer audio application for re-
cording (or any other) purpose. RE7 lets you select whether this feed comprises just synth
sounds, just the signals at the audio inputs, or a mix of the two.
RE8: Not used
Audio Menu Page 4 – Outputs 3 and 4
Outputs 3 & 4 may also carry a mix of synth sounds, the audio sources connected at
Inputs 1 and/or 2, and DAW channels 3 & 4. The default setting for the Output 3+4 mix
is no synth sound and external audio at full level. RE6 provides a balance between DAW
channels 3 & 4 and the mix of audio inputs and synth sounds set up with RE3, RE4, RE5
and RE6.
RE1: Not used, but LCD confirms that this page is concerned with Outputs 3 & 4.
RE2: Synth level
Displayed as: Synth
Default value: 0
Range of adjustment: 0 to 127
RE2 adjusts the level of sounds generated by the synthesiser at Outputs 3 and 4.
RE3: Input 1 level
Displayed as: Input1
Default value: 127
Range of adjustment: 0 to 127
Audio from Input 1 may be mixed into Outputs 3 and 4 by adjusting RE3. With Input Link-
ing (RE1 on Audio Menu Page 1) set to Indept, RE3 adjusts level for Input 1 only. With
Input Linking set to Stereo, the level of both Inputs 1 and 2 will be adjusted as a pair.
To Next Page
Loading...
