Connect
to
your
source devices
NuForce 53-BT can connect
to
your
devices
wirelessly and/or wired.
8/uetooth
Wireless Connection
0 Turn on the
AC
power switch
on
the back
of
the
unit.
8 The Bluetooth
LED
will first light up in blue, then
pairing will initiate in about 2 seconds. with the
8/uetooth
LED
blinking alternatively in red and blue
colors. Note
that
8/uetooth
connection is the default
source selection.
8 Select "NuForce S3-BT" from the
8/uetooth
device
list
of
your
8/uetooth
device. Your
8/uetooth
device
indicates when pairing is complete. The
8/uetooth
LED
on
S3·BT
blinks slowly in blue when pairing
is
complete. (Please consult the user manual
of
your
8/uetooth source devices
for
instructions on how
to
pair them
with
other
8/uetooth
devices)
0
To
change
to
another
8/uetooth
source device, turn
off the
8/uetooth
connection on the current device,
then press and hold the Play/Pause button on the
top control panel
for
a few seconds, this will restart
the pairing process.
0 If pairing is
not
completed in 2 minutes,
S3-BT
will
go
into power-saving mode, with the
8/uetooth
LED
blinking in red.
Press
and hold the Play/Pause button
for a few seconds to re-start pairing.
Wired Connection
0 Connect the analog
output
of
your TV
or
other
source devices
to
S3-BT's
Audio Input
RCA
jacks with
the included
RCA
interconnect cable.
8
Press
the "Source" button on the control panel
to
select "Line-in"
as
the source; The Line-in
LED
will
light up.
Volume
control
and
other
operations
0 Press the "Source" button
to
select between Blue-
tooth
and Line In
as
the
input
source. Note
that
you
may need
to
go
through the pairing process again
when you switch back
from
Line-in to 8/uetooth_
8
Press
the volume button
to
increase
or
decrease the
volume.
8
You
can use the "Previous
track/Next
track"
button
to
jump
to
the previous
or
next track
on
your
8/uetooth device. Note
that
this function works only
with
8/uetooth
devices supporting
AVRCP
profile
(this includes devices running
iOS
4.1
or
later,
Android
1.5
or
later. and Windows Mobile 5.0
or
later).
0 The
USB
charging
port
allows you to charge
your
mobile devices via a
USB
cable. Please refer
to
the
user manual
of
your mobile devices
for
instructions.
Specifications
Speakers
1"
soft
dome tweeter x 2
3.5'"
composite paper cone woofer x 2
Amplifier
Maximum
power
output:
18
Watt x 2
RMS
Harmonic distortion : < 0.5% 1 W 1 kHz
Frequency response :
50
Hz
-
20
kHz
Signal/Noise ratio :
> 75 dB
Separation : > 45 dB
Input/Output
Speaker
output
on
right
channel
unit:
Five-way binding posts
Speaker
input
on
left
channel
unit:
Five·way binding posts
Analog
Input
:
RCA
jacks
USB
Charger
Port:
Sv
.
1A
output
(strictly
for
charging mobile
devices only,
no
audio/data transmitting)
8/uetooth wireless connection :
8/uetooth
core version 4.0
with
aptX.
SBC,
AAC
codecs;
A2DP
and
AVRCP
profiles
(C)
2
01
2,
Nuforce, Inc. All rights reserved.
• The
aptx•
software is copyri
ght
CS
R pic or
it
s group companies. All rights reserved. The
aptX• mark and
the
apt X logo are trade marks
of
CSR
pic
or
one
of
its
group
companies
and may be registered
in
one or more jurisdictions.
••
The 8/uetooth• word mark and logos are registered trademarks owned
by
Bluetooth
SIG,
Inc. and any user
of
such marks by Nuforce, Inc. is under license. Nuforce, the
Nuforce logo and
S3·BT
are trademarks
or
registered trademarks
of
Nuforce, Inc.
USA.
All other trademarks are the property
of
their respective owners.
5
To Next Page
Loading...
General