MODEL: SFL618
Wash hands after handling. This product or
its power cord may contain chemicals known to
the State of Califomia to cause cancer and birth
defects or other reproductive harm.
TOOL USE AND CARE
Know this tool. Read manual carefully, learn
its applications and limitations, as well as the
specific potential hazards related to this tool.
Only use fasteners that are recommended
for your models. Do not use the wrong
fasteners or load the fasteners incorrectly.
Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tool's
operation. If damaged, have the tool serviced
before using. Many accidents are caused by
poorly maintained tools.
Maintain tools with care. Keep tool clean. A
properly maintained tool, reduces the risk of
binding and is easier to control.
Store tools out of the reach of children and
other untrained people. Tools are dangerous
in the hands of untrained users.
Check operation Of the tool before use.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job
better and safer at the rate for which it is
designed.
Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding a tool by hand or
against the body is unstable and may lead to
loss of control.
Keep the tool and its handle dry, clean and
free from oil and grease. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum—based products, or any
strong solvents to clean your tool.
Do not use the tool as a hammer.
Never use this tool in a manner that could
cause a fastener to be directed toward
anything other than the workpiece.
Never use gasoline or other flammable
liquids to clean the tool. Never use the tool in
the presence of flammable liquids or gases.
Vapors could ignite by a spark and cause an
explosion which will result in death or serious
personal injury.
Always fit tool with a fitting or hose
coupling on or near the tool in a way that all
the remaining compressed air in the tool is
discharged at the time the fitting or hose
coupling is disconnected. Do not use a check
valve or any other fitting which allows air to
remain in the tool. Death or serious personal
NL.ounÄ
Never carry the tool by the air hose or pull
the hose to move the tool or a compressor.
Keep hoses away from heat, oil and sharp
edges. Replace any hose that is weak, wom, or
otherwise damaged. Personal injury or tool
damage could occur.
Always assume the tool contains fasteners.
Respect the tool as a working implement; no
horseplay.
Do not drop or throw the tool. Dropping or
throwing the tool can result in damage that will
make the tool unusable or unsafe. If the tool
has been dropped or thrown, examine the tool
closely for an air leak or bent, cracked or broken
parts. STOP and repair before using, or serious
injury could occur.
Avoid using the tool when the magazine is
empty. Accelerated wear on the tool may
occur.
Clean and check all air supply hoses and
fittings before connecting the tool to an air
supply. Replace any damaged or worn hoses
or fittings. Tool performance or durability may
be reduced.
Always carry the tool by the handle. Never
carry the tool by the air hose.
Do not use the tool if it leaks air or does not
function properly.
Do not operate the tool if it does not
contain a legible warning label.
TOOL SERVICE
Only use accessories that are identified by
the manufacturer for the specific tool model.
Use of unauthorized parts or failure to
follow maintenance instructions may
create a risk of injury.
Only use the lubricants supplied with the
tool or specified by the manufacturer.
Tool service must be performed only by
qualified repair personnel.
OPERATION
Do not drive fasteners near edge of
workpiece. The workpiece may split causing
the fastener or ricochet, potentially injuring you
or people around you.
Do not drive fasteners on top of other
fasteners or with the tool at an overly steep
angle as this may cause deflection of
fasteners which could cause injury.
Do not actuate the tool unless you intend to
drive a fastener into the workpiece.
Always handle the tool with care:
Respect the tool as a working implement.
Never engage in horseplay.
Keep others a safe distance from the tool
MODEL: SFL618
UNPACKING
while tool is in operation as accidental
actuation may occur, possibly causing
O This tool has been shipped completely
injury.
assembled.
AIR SUPPLY AND CONNECTIONS
Carefully remove the tool and any
O The connector on the tool must not hold
accessories from the box.
pressure when air supply is disconnected. If
O Inspect the tool carefully to make sure no
an incorrect fitting is used, the tool can remain
breakage or damage occurred during
charged with air afterdisconnecting and thus will
shipping.
be able to drive a fastener even after the air line
Do not discard the packing material until
is disconnected,possiblycausing injury.
you have carefully inspected and
Do not use oxygen, combustible gases or
satisfactorily operated the tool.
bottled gases as a power source for this tool.
If any parts are damaged or missing, please
An explosion may occur, causing injury or
call 1-888-669-5672.
death.
Do not use any type of reactive gases,
including, but not limited to, oxygen and
A WARNING:
combustible gases, as a power source. Use
If any parts are missing do not operate
filtered, lubricated, and regulatedcompressed air
this tool until the missing parts are
only. Use of a reactive gas instead of
replaced. Failure to do so could result in
compressed air may cause the tool to explode
possible serious personal injury.
which will cause death or serious personal injury.
Use only a pressure—regulated compressed
air source to limit the air pressure supplied
to the tool. The regulated pressure must not
A WARNING:
exceed 115 psi. If the regulator fails, the
pressure delivered to the tool must not exceed
Do not attempt to modify this tool or
115 psi. The tool could explode which will
create accessories not recommended for
cause death or serious personal injury.
use with this tool. Any such alteration or
Always disconnect air source:
modification is misuse and could result
in hazardous condition leading to
Before unloading or making adjustments.
possible serious personal injury.
• When maintaining the tool.
When clearing a jam.
When touching the safety yoke.
FEATURES
When tool is not in use.
When moving to a different work area.
SPECIFICATIONS
Such precautionary measures reduce the risk
of injury to persons.
LOADING TOOL
Do not load the tool with fasteners when
any one of the operating controls is
activated.
Never place a hand or any part of body in
fastener discharge area of tool.
O Never point tool at anyone.
A WARNING:
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
HTTP://WWW. NUMAXTOOLS. COM
Operation pressure:
Magazine capacity:
Tool weight:
Air inlet:
70-115 psi
L: 100 pcs
T: 100 pcs
U: 120 pcs
1 1.46 lbs
Fasteners length range: 1—1/2in. to 2 in.
T cl eats
38m m 1 -1/2'
45mm I -3/4'
50mm 2"
Lcleats
38m m 1
45m m I - 3/4•
50mm 2"
38mm
45m m
50mm
1-1/2"
1-3/4"
(16 Gauge)
injury could occur.
04
HTTP://WWW. NUMAXTOOLS. COM
1-888-669-5672
(16 Gauge)
1-888-669-5672
•15—112Gauge)
0.075" x 0.063"
1.9x 1.6mm
05
To Next Page
Loading...
