NXP Semiconductors MPC5777M - Page 162

MPC5777M Microcontroller Data Sheet, Rev. 6
Document revision history
NXP Semiconductors162
4 9/2014
Electrical characteristics—DC electrical specification
•In Section 3.1, Introduction, added the following to note text: "V
DD_HV_ADV
refers to
ADC supply pins V
DD_HV_ADV_S
and V
DD_HV_ADV_D
. V
DD_HV_ADR
refers to ADC
reference pins V
DD_HV_ADR_S
and V
DD_HV_ADR_D
. V
SS_HV_ADV
refers to ADC ground
pins V
SS_HV_ADV_S
and V
SS_HV_ADV_D
. V
SS_HV_ADR
refers to ADC reference pins
V
SS_HV_ADR_S
and V
SS_HV_ADR_D
."
•In Table 10 (DC electrical specifications), changed I
DD_HV_PMC
maximum for PMC only
condition (was 5 mA, is 25 mA). Added “This includes PMC consumption, LFAST PLL
regulator current, and Nwell bias regulator current” to footnote associated with this
value.
•In Table 10 (DC electrical specifications), changed I
DD_LV
maximum to 1140 mA (was
600 mA) and added “V
DD_LV
= 1.325 V” to conditions.
•In Table 10 (DC electrical specifications), added I
DDAPP_LV
specification.
•In Table 10 (DC electrical specifications), changed the conditions for I
DDSTBY_RAM
and
I
DDSTBY_REG
(were “...to 6 V...”, are “...to 5.5 V...”).
•In Table 10 (DC electrical specifications), I
DDSTBY_RAM
specification: changed max
value for 40°C condition to 60 µA (was 40). Changed max value for 85°C condition to
100 µA (was 60).
•In Table 10 (DC electrical specifications), V
STBY_BO
specification: changed min value
to 0.9 V (was 0.8).
Electrical characteristics—I/O pad current specification
• Table 12 (I/O input DC electrical characteristics), Table 13 (I/O pull-up/pull-down DC
electrical characteristics), Table 14 (WEAK configuration output buffer electrical
characteristics), Table 15 (MEDIUM configuration output buffer electrical
characteristics), Table 16 (STRONG configuration output buffer electrical
characteristics), Table 17 (VERY STRONG configuration output buffer electrical
characteristics), Table 19 (I/O consumption) added the following footnote to Conditions
heading: “During power up operation, the minimum required voltage to come out of
reset state is determined by the V
PORUP_HV
monitor, which is defined in the voltage
monitor electrical characterstics table. Note that the V
PORUP_HV
monitor is connected
to the V
DD_HV_IO_MAIN0
physical I/O segment.”
• Table 12 (I/O input DC electrical characteristics): V
HYSTTL
specification: changed min
value to 0.275 (was 0.3). V
HYSAUT
specification: changed min value to 0.4 (was 0.5).
• Table 12 (I/O input DC electrical characteristics), changed V
IHCMOS_H
min value to
“0.70 * V
DD_HV_IO
” (was 0.65 * V
DD_HV_IO
).
•In Table 12 (I/O input DC electrical characteristics), changed V
IHAUT
min value to 3.9 V
(was 3.8).
• Table 12 (I/O input DC electrical characteristics), revised I
LKG
and I
LKG_EBI
rows.
Table 76. Revision history (continued)
Revision Date Description of changes