How to fix WaterMe Nymet Controller when it is unable to connect to the network?
If your WaterMe is unable to connect to the network and there's no solid green status light, ensure that you've entered the correct SSID and password during the smart configuration process. Also, verify that the network cable is securely connected and undamaged.
What to do if the flow sensor is not working correctly on my Nymet Controller?
If the flow sensor on your Nymet Controller is not working correctly, check the connections to ensure that the correct wires are connected to the terminal block. Also, make sure that the flow sensor does not have any debris trapping the impeller.
Why Wi-Fi doesn’t connect during the WaterMe Nymet Controller activation process?
If your Wi-Fi doesn’t connect during the WaterMe Nymet Controller activation process, and you have more than one controller connected to the Wi-Fi network, WaterMe will not connect. Disconnect the power from the currently active controller and restart the activation process.
What to do if the status light is not lit on my Nymet WaterMe?
If the status light on your Nymet Controller is not lit, it should always be on, displaying red, green, or a combination of both. First, check that the power pack is securely connected to the WaterMe device. Then, ensure power is available at the socket outlet.
What to check if the solenoid valves do not operate on my Nymet WaterMe?
If the solenoid valves of your Nymet Controller do not operate, check the physical connections to the solenoids to ensure they are in place. Verify the correct solenoid valve voltage. Confirm that the correct settings for 24VAC/DC latching are selected within the settings screen on your mobile or web interface. Also, ensure the solenoid valve wire is secured to the correct zone valve terminal connection and that the other wire is securely connected to the ground of the terminal strip.
What to do if no zones are passing water but zone LEDs are active on my Nymet Controller?
If no zones are passing water but the zone LEDs are active on your Nymet Controller, check the wiring connection to the master valve and ensure that the master valve is operational.
What to do if there is unusual behavior from the Nymet Controller?
If you observe unusual behavior from the Nymet Controller, switch it off, wait 10 seconds, and then switch it back on.
General| Brand | Nymet |
|---|---|
| Model | WaterMe |
| Category | Controller |
| Language | English |
Instructions for downloading the mobile application for device control.
Details on how to get user support and access product updates.
Indicates additional information, important contents, or tips for installation.
Highlights something of importance that should be acknowledged.
Indicates a hazard that could cause damage or injury if not avoided.
Explains the meaning of different LED light combinations for connection status.
Caution against using non-approved components to avoid damage and voiding warranty.
Lists items needed before installing and connecting the WaterMe controller.
Lists minimum requirements for the WaterMe controller to operate successfully.
Diagram and explanation of how the controller connects to the WaterMe server.
Identifies external components and their functions on the controller.
Identifies internal components and their functions on the controller.
Connects via Wi-Fi using a smartphone app for configuration.
Connects via Wi-Fi using a PC for configuration.
Detailed steps for connecting via Wi-Fi using a mobile phone.
Steps to register the device on the WaterMe server via mobile.
Steps to connect via Wi-Fi using a PC for configuration.
Steps to register the device on the WaterMe website.
Explains SSID (Network Name) and Password (Network Key).
Guidance on locating Wi-Fi network settings.
Cautions regarding sunlight, weather, and power proximity for controller placement.
Advice on mounting position and spacing for optimal performance and longevity.
Wire output via bottom conduit for valve wires.
Wire output via rear conduit for hidden wires.
Caution on making incisions for wire passage to prevent water ingress.
Cautions on upright position and O-rings during controller mounting.
Details terminal inputs for power, sensors, and valves.
Example of wired connections for standard installation.
Explains flow sensor wiring and pinouts.
Warning against connecting flow sensor ground with solenoid grounds.
Steps for inserting and tightening wires into terminals.
Cautions on correct input placement and avoiding overtightening.
Warning against forcing the front housing and ensuring proper fit.
Guidelines for installing the flow sensor for optimal life and accuracy.
Details flow sensor specifications and functional requirements.
Illustrates recommended placement between master and solenoid valves.
Warning about connecting grounds during flow sensor wiring.
Connects moisture sensor to controller for calibration.
Connects rain sensor to controller for calibration.
How to access the web interface via URLs.
Options to log in or register on the website.
What to expect after successful registration.
Explains the main source of statistical information for the controller.
Details how the summary screen displays during a watering cycle.
Explains how to add, edit, and delete zones.
Steps to add new watering zones to the system.
How to change the display image for each zone.
Steps to edit the name of an existing zone.
Process for deleting a zone from the system.
How to run watering cycles manually and test zones.
Instructions for activating/deactivating zones via manual screen.
Explains setting up recurring watering schedules.
Step-by-step guide to creating new watering schedules.
How the system alerts and allows resolution of overlapping schedules.
Overview of the weather interface for automatic adjustments.
Steps to configure weather rules based on location and forecast.
How to choose local weather stations for accurate forecasts.
Configuring parameters for watering adjustments based on rain forecasts.
Configuring parameters for watering adjustments based on temperature.
Detailed explanation of various controller settings and their functions.
Steps to calibrate the system for accurate flow rate recording.
Steps to remove your device and settings from the WaterMe server.
Details the mobile app's summary screen for stats and zone management.
How to add new zones using the mobile app.
How to customize zone images via the mobile app.
How the app notifies users of irrigation system errors.
How to scroll and view individual zone panels in the app.
How to switch between percentage and time display for watering.
How to use the manual screen for watering control.
Steps to turn zones on/off via the manual mobile screen.
Steps to customize watering schedules in the mobile app.
Steps to calibrate flow using the mobile app's settings.
Details the mobile app's settings screen for adjustments.
How to toggle between mist and continuous watering modes.
Explanation of solenoid valve types and voltage drop.
Configure master and zone delays between valve activations.
How to adjust flow sensor calibration values.
How to set tolerance for flow rate error reporting.
How to choose automatic responses to system errors.
How to ensure mobile alerts and emails for system errors.
Overview of the mobile weather interface for automatic adjustments.
Steps to configure weather rules via mobile.
How to set up the weather schedule in the mobile app.
Lists common issues and their resolutions for the controller.
Conditions under which warranty claims are excluded.
Company overview as a manufacturer of solenoid valves.
Provides company contact details for inquiries.
To Next Page