Olympus VP-10 - Menu and Settings Configuration

EN
4
NOTE:
•
Before
connecting
the
USB
connector, release
HOLD
mode.
Before charging
the
battery,
insert
the
rechargeable
battery
provided
and set
[Battery]
to
[Ni-MH].
1 Start the
PC.
2
Remove
the
USB
connector
cover.
• Slide
open
the
USB
connector
cover using
the
pad
of
your
finger.
After
making
sure
the
voice
recorder
is
stopped,
connect
the
USB
connector
to
a
USB
port
on
a
PC.
4
Press
the
OK
button
to
start
charging
the battery.
• When
[Battery]
is
set
to
[Ni-MH],
[OK=
Charging]
appears on
the display.
Press
the
OK
button
while this message
is
blinking.
5
Charging
is
finished
when
[Battery
full]
appears.
NOTE:
•
Never
attempt
to
charge an
alkaline battery,
lithium
battery
or
other
primary
cell battery. Fluid
leakage
or
overheating
may cause
the
recorder
to
malfunction.
1
Slide
the
POWER/HOLD
switch
in
the
direction
of
the
arrow
for
at
least
half
a
second.
Auto
power
off
mode
When
the
voice recorder has been
stopped
for
at least 5
minutes
(default setting)
after
power
ON,
the
display disappears and
the
voice
recorder
automatically
turns off.
•
To
reuse
the
recorder,
turn
the
power
ON
again.
•
The recorder
will
not
be
turned
off
during
recording, even
if
the
POWER/HOLD
switch
operated.
Recording
1
Point
the
built-in
microphone
in
the direction
of
the
sound
to
record.
2
Slide
the
REC
switch
to
start
recording
in
the
direction
of
the
arrow.
@Recording
indicator
@Current
file
number
in
folder/
Total
number
of
recorded files
in
folder
@Elapsed
recording
time
• The
LED
indicator
light
lights,
and
[eJ
appears in
the
display.
•
After
replacing
the
battery,
turn
on
the
power
and
then
make sure you set
the
settings
on
the
[Battery]
screen and
[Time
&
Date]
screen before
recording.
3
Slide
the
REC
switch
to
stop
recording
in
the direction ofthe
arrow.
• [
•]
appears in
the
display.
NOTE:
•
When
recording
with
the
voice
recorder in a
pocket
or
alike,
secure
it
with
a
clip
to
prevent
if
from
moving.
The voice recorder has pre-registered
templates
of
optimum
settings
tailored
to
various
recording
applications such
as
conference
and
dictation.
When selecting
one
of
these templates you can
enter
several settings
recommended
for
your
recording
application
all
in a
single
operation.
1
While
the
voice
recorder
is
in
stop
mode,
press
and
hold
the
MENU/
SCENE
button.
2
Press
the
OK
button.
3
Press
the+
or-
button
to
select
the
desired
recording
application.
4
Press
the
OK
button
to
finalize
the
setting.
You can change
the
information
screen
during
recording.
1
Press
the
OK
button
during
recording.
Each press
of
the
OK
button
changes
the
information
screen.
@Elapsed
recording
time
screen
(default
setting)
You can display
the
elapsed
recording
time
and
current
file
number
in folder.
@Recording
level
meter
screen
The
meter
changes according
to
recording
volume
and
recording
function
setting.
©Functions
indicator
screen
You can display
the
indicator
offunctions
and remaining
recording
time.
@Date
and
time
screen
You can display
the
current
date
and time.
NOTE:
• The
information
screen
return
to
default
screen
if
the
voice recorder
will
be changed
to
other
operation
(stop, playback, recording).
•
Meanings
of
indicators
(same
for
all
modes)
[
Ni
]:
Battery
type
[1]11]:
Possible
recording
time
[~]:Noise
Cancel
[~]:Voice
Balancer
[~H]:
Rec
Level
[X]:
Low Cut
Filter
[Iii]:
Anti-Rustle
[120]:
Rec
Mode
[~H!rnj]:
Rec
Scene
[
~
]:
Play Scene