EasyManua.ls Logo

Omron NJ501-1320 - Page 294

Omron NJ501-1320
400 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Appendices
A-10
NJ-series CPU Unit Hardware User’s Manual (W500)
* The ON response time will be 20 s maximum and OFF response time will be 400 s maximum even if the response times
are set to 0 ms due to internal element delays.
Note Observe the following restrictions when connecting to a 2-wire sensor.
Make sure the input power supply voltage is larger than the ON voltage (19 V) plus the residual voltage of the sen-
sor (approx. 3 V).
Use a sensor with a minimum load current of 3 mA min.
Connect bleeder resistance if you connect a sensor with a minimum load current of 5 mA or higher.
CJ1W-ID233 DC Input Unit (24 VDC, 32 Points)
External connection and
terminal-device variable
diagram
The input power polarity can be connected in either direction.
Be sure to wire both pins 23 and 24 (COM0), and set the same polarity for both pins.
Be sure to wire both pins 3 and 4 (COM1), and set the same polarity for both pins.
Name 32-point DC Input Unit with MIL Connector
Model CJ1W-ID233
Rated Input Voltage 24 VDC
Allowable Input Voltage
Range
20.4 to 26.4 VDC
Input Impedance 5.6 k
Input Current 4.1 mA typical (at 24 VDC)
ON Voltage/ON Current 19.0 VDC min./3 mA min.
OFF Voltage/OFF Current 5 VDC max./1 mA max.
ON Response Time
8.0 ms max. (Can be set to between 0 and 32 ms in the Unit Information settings.)
*
OFF Response Time
8.0 ms max. (Can be set to between 0 and 32 ms in the Unit Information settings.)
*
Number of Circuits 32 (16 points/common, 2 circuits)
Number of Simultane-
ously ON Points
75% (12 points/common) simultaneously ON (at 24 VDC) (Refer to the following illustration.)
Insulation Resistance 20 M between external terminals and the GR terminal (100 VDC)
Dielectric Strength
1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA
max.
Internal Current Con-
sumption
200 mA max.
Weight 70 g max.
Accessories None
Wd m+1
Wd m+1
Wd m
Wd m
24 VDC
24 VDC
Signal
name
Signal
name
Connec-
tor pin
Allocated
CIO word
Allocated
CIO word
2
NC
4
COM1
6
Jxx_Ch2_In07
8
Jxx_Ch2_In06
10
Jxx_Ch2_In05
12
Jxx_Ch2_In04
14
Jxx_Ch2_In03
16
Jxx_Ch2_In02
18
Jxx_Ch2_In01
20
Jxx_Ch2_In00
Jxx_Ch1_In07
Jxx_Ch1_In06
Jxx_Ch1_In05
Jxx_Ch1_In04
Jxx_Ch1_In03
Jxx_Ch1_In02
Jxx_Ch1_In01
Jxx_Ch1_In00
22
NC
24
26
28
30
32
34
36
1
NC
3
COM1
5
Jxx_Ch2_In15
7
Jxx_Ch2_In14
9
Jxx_Ch2_In13
11
Jxx_Ch2_In12
13
Jxx_Ch2_In11
15
Jxx_Ch2_In10
17
Jxx_Ch2_In09
19
Jxx_Ch2_In08
21
NC
23
25
27
29
31
33
35
38
40
37
39
COM0
COM0
Jxx_Ch1_In15
Jxx_Ch1_In14
Jxx_Ch1_In13
Jxx_Ch1_In12
Jxx_Ch1_In11
Jxx_Ch1_In10
Jxx_Ch1_In09
Jxx_Ch1_In08

Table of Contents

Related product manuals