EasyManuals Logo

Onkyo HT-R490 User Manual

Onkyo HT-R490
36 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #11 background imageLoading...
Page #11 background image
11
Rear panel facilities
9 z (REMOTE CONTROL)
Connect the Onkyo components that have z connectors such as a
CD player, and cassette tape deck using the z cables provided
with them. When these components are interconnected, they can be
controlled from the remote controller provided with the HT-R490.
After connecting the z connectors, check the operation of the
remote controller buttons for use in controlling other components
(refer to page 30).
For remote control operation, the audio connection cables
must also be connected.
If the connected component has two z connectors, you can
use either one to connect to the HT-R490. The other one can be
used to daisy chain with another component.
p AC OUTLETS
The HT-R490 is supplied with AC mains outlets for connecting
the power cords from other devices so that their power is supplied
through the HT-R490. By doing this, you can use the STANDBY/
ON button on the HT-R490 to turn on and off the connected
devices as well.
7 DIGITAL INPUT (OPTICAL/COAXIAL)
There are 2 digital inputs, one with a coaxial jack and the other
with an optical jack. The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source component.
When using the optical input jack, remove the protective cap
and keep it safely. When the jack is not used, replace the
protective cap.
When using an optical input jack, always use an optical fiber
cable.
When using the digital inputs, make sure to also connect the
analog connections whenever possible.
8 MULTI CHANNEL INPUT
By connecting a DVD player, MPEG decoder, or other component
that has a multi channel port, you can playback the audio with 5.1
channel output. So, be sure to prepare a cable that can properly
connect the HT-R490 to the peripheral device.
Connect the video output to one of VIDEO IN connectors
(DVD, VIDEO 1 and VIDEO 2).
Optical fiber cable
Coaxial cable (RCA type)
AC OUTLETS
AC 120V 60Hz
SWITCHED
TOTAL 120W 1A MAX.
REMOTE
CONTROL
Ex: Onkyo CD player
Ex: Onkyo cassette
tape deck
HT-R490
z connector
z connector
L
L
R
R
FRONT
CENTER
SURR
SUB
WOOFER
RL
COAXIAL
A
B
FRONT
SPEAKERS
IN
OUT
VIDEO
IN
IN
MULTI
CHANNEL INPUT
1
2
3
7
4
5
6
DVD player/MPEG decoder
Ex: Onkyo DVD Player
1. Front right
2. Surround right
3. Center
4. Front left
5. Surround left
6. Subwoofer
7. Video
Other components
COAXIAL
OPTICAL
Caution:
Make sure that the total capacity of the other components
connected to this unit does not exceed the capacity that is printed
on the rear panel (120 watts).

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Onkyo HT-R490 and is the answer not in the manual?

Onkyo HT-R490 Specifications

Amplifier Section IconAmplifier Section
continuous average power output (FTC) - 8 ohms55 watts per channel min. RMS
continuous average power output (FTC) - 6 ohms70 watts min. RMS
continuous power output (DIN)75 watts × 5 at 6 ohms
maximum power output (EIAJ)100 watts × 5 at 6 ohms
total harmonic distortion0.08% at rated power (Front)
IM distortion0.08% at rated power (Front)
damping factor60 at 8 ohms (Front)
input sensitivity and impedance - LINE200 mV, 50 kohms
input sensitivity and impedance - MULTICHANNEL INPUT (FRONT L/R, SURROUND L/R, CENTER)200 mV, 50 kohms
input sensitivity and impedance - MULTICHANNEL INPUT (SUBWOOFER)36 mV, 50 kohms
input sensitivity and impedance - DIGITAL 2 (COAXIAL)0.5 Vp-p, 75 ohms
output level and impedance - Rec out (TAPE, VIDEO 2)200 mV, 2.2 kohms
output level and impedance - Pre out (SUBWOOFER)1 V, 2.2 kohms
frequency response20 Hz to 100 kHz, +1/–3 dB
RIAA deviation20 Hz to 20 kHz, ±0.8 dB
tone control - Bass±10 dB at 50 Hz
tone control - Treble±10 dB at 10 kHz
signal-to-noise ratio - CD/Tape100 dB (IHF-A)
Tuner Section IconTuner Section
FM tuning range87.5-108.0 MHz (50 kHz steps)
FM usable sensitivity - Mono11.2 dBf, 1.0 µV (75 ohms)
FM usable sensitivity - Stereo17.2 dBf, 2.0 µV (75 ohms)
FM 50 dB quieting sensitivity - Mono17.2 dBf, 2.0 µV (75 ohms)
FM 50 dB quieting sensitivity - Stereo37.2 dBf, 2.0 µV (75 ohms)
FM capture ratio2.0 dB
FM image rejection ratio40 dB
FM IF rejection ratio90 dB
FM signal-to-noise ratio - Mono76 dB
FM signal-to-noise ratio - Stereo70 dB
FM alternate channel attenuation55 dB
FM selectivity50 dB (DIN)
FM AM suppression ratio50 dB
FM total harmonic distortion - Mono0.2%
FM total harmonic distortion - Stereo0.3%
FM frequency response30 Hz-15 kHz, ±1.0 dB
FM stereo separation45 dB at 1 kHz
AM tuning range530-1, 710 kHz (10 kHz steps)
AM usable sensitivity30 µV
AM image rejection ratio40 dB
AM IF rejection ratio40 dB
AM signal-to-noise ratio40 dB
AM total harmonic distortion0.7%
General IconGeneral
power supplyAC 120 V, 60 Hz
power consumption3.4 A
dimensions (W × H × D)435 × 150 × 339 mm
weight9.7 kg, 21.4 lbs.

Related product manuals