Onkyo TX-904 - Page 14

M@ How to cancel memorized stations
Retrieve the class number you want to cancel (see “How to
retrieve memorized stations”) and then press the MUTE/MODE
button while holding down the MEMORY button. Another
station can be memorized with the memory number which has
been cancelled.
CLASSIFIED
MEMORY FM MUTE/MODE SCAN
L— ERASE
M@ How to retrieve memorized stations
1) Press the Classified Memory button for the desired class.
If remote contro! is used, the class next to the present one
is retrieved when the CLASS button is pressed.
@ The memory number (station) which was being received
before the class is retrieved will be received.
(2) There are several methods to proceed after the above oper-
ations are carried out. Use any of the following methods.
a. Pressing the same Classified Memory button again per-
mits the next preset memory number (station) to be re-
ceived.
b. Input the memory number you wish to receive by using
the Number buttons.
® if the memory number consists of 2 digits, input two
numbers, immediately one after the other. For instance,
when inputting “15”, “15” will not be registered if
you wait more than one second before inputting “5”,
resulting in only “1” being registered.
@ if a number other than a number from 1 to 40, or a
number which has not been memorized is input, the
number flashes for 2 seconds and then the number
which was displayed before will be displayed.
@ \f a number between 1 and 4 is pressed, the display
and station are changed 1 second Iater.
c. Press the CLASSIFIED SCAN button
@ Stations memorized in the present class will be
scanned in a order and the corresponding memory
number will flash in the Preset station display at each
scan. After the last memory number of the class is
reached, scanning starts again from the first memory
number of the class. Pressing the CLASSIFIED SCAN
button again stops scanning.
d. When the PRESET UP or DOWN button of the remote
controfier is pressed, the memory number of the class
currently being received will be incremented or decre-
mented. Keeping pressing the button increments or de-
crements continuously. After the maximum or minimum
number is reached, the next class or one before the present
class will be entered.
Tape Recording
With
the
TX-906/904
you
can
perform
recording
while
listening
to
the
sound
of
another
source
through
speakers
or
headphones.
Make
al!
connections
between
the
tape
deck
and
the
unit
as
shown
in
the
System
Connections
diagram.
M Recording and dubbing to a tape deck connected to TAPE-1
(When recording the source you are listening to)
0 Sk
@@ REC OUT
Tape Deck
© Source required
Source selected in (1)
(4) Starting
Source selected
in 1)
(4) Starting tape
deck recording
(When recording a source different from the one you are listening to)
oO "
© REC OUT
Tape Deck
2) Source required
Source selected in @)
(3) Starting tape
deck recording
Source selected
in @)
(1) Press the input selector button to select the source to be re-
corded. (Other than TAPE-1)
Press the REC OUT button.
e on the display flashes for 8 seconds.
(3) Press the REC OUT button again while the indi-
cator is flashing.
e and [SOURCE] will light, and the indication
of the source selected by the input selector button wil! be
marked with a red frame.
(4) Start the device selected in step (1), while setting the tape deck
connected to TAPE-1 to recording mode.
@ Set the proper recording level using the controls on the tape
deck used for recording. Also, during recording and dubbing
operations, never change the positions of any controls (bass,
treble, etc.) on this unit.
NOTES:
@ Pressing the input selector button during recording will
change the source being recorded.
@® When the TAPE-2 MONITOR indicator is on, only TAPE-2
S)
can be recorded and if the input selector is changed, the red
frame of TAPE-2 will not change.
a Press the REC OUT button.
@ [REC OUT > on the display will flash for 8 seconds.
(2) Press the input selector button for the source to be recorded
while the indicator is flashing. (Other than
TAPE-1)
e will light and the indication of the source
selected will be marked with a red frame. This source will
be output from the REC OUT jacks of TAPE-1, VIDEO-2.
The source you are listening to does not change.
(3) Start the source device selected in step (2), and start recording
on the tape deck connected to TAPE-1.