Onkyo TX-SV424 - Basic Operations Guide; Power and Speaker Selection; Volume, Tone, and Balance Controls

Basic
operations
MASTER VOLUME
STAND-BY/RECEIVED INDICATOR
The
STAND-BY/RECEIVED
indicator
comes
on
when
the
AC power cord for this unit has been inserted in an outlet.
This
indicates
that
this
unit
is
standing
by
for
operation.
Press
the
POWER
button
will
turn
the
main
unit
on,
then
this
indicator goes off.
The
indicator
also
lights
when
a
signal
is
received
from
the
remote control.
SPEAKERS SELECTOR
SPEAKERS A: This ‘button turns on or off the speakers
connected to the FRONT A, CENTER and REAR SPEAK-
ERS terminals. When the speakers are turned on, the
SPEAKERS A indicator lights up.
SPEAKERS
B:
This
button
turns
on
or
off
the
speakers
connected to the FRONT B SPEAKERS terminals. When
the speakers are turned on, the SPEAKERS B indicator
lights up.
@ With U.S.A. model, Speaker A and B can be used at the
EST
TIN
co
cot
USE
IL
EES
NUIT
IU
EUS
SEES
a
perro
maaan)
Pe
Same
time.
@ Other models, cannot be used at the same time. When
one button is pressed, the other button is automatically
e turned off.
TOAC outlet # MASTER VOLUME CONTROL
Use this knob to adjust the volume of the Front, Center, Rear
(Surround) speakers.
TONE AND BALANCE CONTROLS
Treble, Bass and Selective Tone are effectively only for the
Front left and right speakers.
The
best
results
are
obtained
from
DOLBY
PRO
LOGIC
Surround
when
the
Center
and
Front
left
and
right
speakers
contain the same amounts of mid and high frequencies. As
the Treble and Bass control do not affect the Center speaker,
meassiestceserapmanandaneasumaiswermmanius
adjust
the
tone
controls
for
the
Front
left
and
right
speakers
to
oe
match
the
sound
given
by
the
Center
speaker.
Because
of
SPEAKERS
.
.
A
B
this,
we
recommend
the
use
of
a
good
quality
Center
speaker.
Cf)
BASS:
Adjust
to
strengthen
or
weaken
bass
response.
ceeoeneum
reece
saneemeaaeaes
TREBLE:
Adjust
to
strengthen
or
weaken
treble
response.
SELECTIVE TONE: This control is used to clearly repro-
duce ultra low and high frequencies, and only affects the
Front
speakers.
When
this
control
button
is
pressed,
the
SELECTIVE TONE indicator lights up.
BALANCE: Use to adjust the relative volume levels of the
right and left Front speaker systems. This adjusts the relative
volume level of the Front speakers only.
SELECTIVE TONE
INPUT SELECTOR
SPEAKERS A, B
STAND-BY/RECEIVED BASS
indicator
TREBLE
BALANCE
INPUT SELECTOR
TAPE-1 TAPE-2 TUNER PHONO
Before plugging in the unit, confirm that all connections
have been made properly.
1.
Insert
the
AC
power
supply
cord
into
the
wall
outlet.
Sissons paneer meats The STAND-BY/RECEIVED indicator comes on.
2. Press the POWER button to turn on the power.
The display lights up and the STAND-BY/RECEIVED
indicator goes off.
3. Press the SPEAKERS A button.
SPEAKERS A indicator lights up.
4. Press the desired input selector button (e.g. PHONO).
The appropriate letters (e.g. PHONO) appear on the display.
4
Confirm
that
the
T-2
MONITOR
indicator
is
off
when
a
{ne
AEE
source
other
than
the
TAPE-2
MONITOR
has
been
selected.
Also
check
the
audio
muting
is
off.
5.
Start
the
selected
input
source
playing.
BALANCE
Follow
the
operating
instructions
of
that
unit.
;
6.
Adjust
the
volume
to
appropriate
level
using
the
MASTER
VOLUME
control
knob
or
VOLUME
A
(up)/
VV
(down)
buttons
on
the
remote
control.
7.
Adjust
the
tone
controls
for
your
desired
tone.
MASTER VOLUME