Note：Please confirm that the PD devices are complying with IEEE802.3af/at standard.
!
Indicator Description
Power LED：PWR
Yellow LED ON
Normal Power Supply
OFF
Power OFF
PoE Working LED:PoE
Green LED ON
Connected the PD Device, Working Normally
OFF
Not Connected the PD Device or Power OFF
Green LED Blink
Green LED ON
Link/ACT LED
Green LED Blink
Data Transmission Normally
Green LED ON
Connected Normally and Working Normally
OFF
Not Connected
Indicator
Status
Description
POWER PORT Gigabit switch series products comes with built-in power, no power adapter,
AC100 ~ 240V, 50/60Hz
：
PoE PORT PoE port with PoE function, w： hich can transmit data and power simultaneously if connected
matching device. The LED lights on the front panel can show working status of each port.
Ethernet PORT：Beside PoE port, other ports are Ethernet RJ45 por t, and all RJ45 port suppor t Auto
MDIMDIX, plug and play. The LED lights on the front panel can show working status of each port.
SFP LED
Data Transmission Normally
Connected Normally and Working Normally
OFF
Not Connected
Green LED Blink
Short Circuit or Current Overload
Installation
Please confirm the following things before installation:
1. If the POE port power meets the power requirement of the connecting devices.
2. If the POE standard requirement and power supply matches with the power receiving device
(1/2+、3/6-( End -span)/ 4/5+、7/8-(Mid-span))
3. If the output power of the matched power adapter is compatible with the specification in the label of the POE switch
Please install the POE switch according to the following steps:
1. Put the PoE switch on the surface of a large and stable table.
2 .Connect the power outlet through the power cable.
3 .Connect the network devices to the POE switch port though network cable.
Installation Guide
!
!
Please install with the matched devices.
Note:
1. Please do not put heavy products on the POE switch, and please ensure good ventilation environment
for the POE switch.
2. Please cut off the power first before plugging the power adapter.
Connect the power cable, plug it into power socket, turn on the power, then the switch will automatically initialize,
and LED lights status will display as following:
1. Except the POE port lights, all the other lights will go through the process of “on-off-on-off”, which means the
restoration is successful.
2. Power LED remains lit.
Power
Note: If initialization is inconsistent with the above, please check the power.
Connection Diagram
Ca
t.
5 Ca
b
le
Powe
r
P
o
E S
w
itc
h
P
oE 3
3
024P
F
M
on
i
to
r
C
at.
5 Ca
bl
e
N
V
R
Vi
deo l
ine
F
i
be
r m
ed
ia
conv
e
r
te
r
PoE
Ca
m
e
r
aIP
I
P
C
am
e
ra
P
oE S
plit
t
e
r
P
D 3
101
D
C OU
T
C
at.5 Ca bl e
PD-Powered Device
Power over Ethernet Splitter
OFF:12V
ON:5V
PoE RUN
PoE IN
DC
OUT
DC RUN
Ethernet out
IN
OUT
PoE I
P
C
a
me
r
a
PoE I P
C
amera
Products Model & Description
Email：onv@onv.com.cn
Address：Room 1003, Block D, Terra Building, Chegongmiao, Futian District, Shenzhen, China
Factor y Address：No 5, A building, SenYuTai S&T park , Longhua road, BaoAn district,Shenzhen, China
Fax：0755-33376608
Tel：0755-33376606
www.onvcom.com
After installation, please check:
If there is enough space for heat sink; if the power socket is suitable for switch specification; if the
power, switch and rack are properly grounded and if the connection between switch and other net-
work equipments are normal.
Power Supply Installation Display
Hangers Installation Display
Rack Installation Display
1
2
3
4
5
6
7
8
100M
1000M
PWR
10
/
100/
1000M
PoE
Switch
Power
Over
Ethernat
Gigabit PoE Switch
LINK PoE
ONV-P 3 PF 16-Port 10/100/1000M PoE switch，transmission distance is 100 meter,1-16 port support PoE，IEEE 802.3af/at,OE3 016 ：
the total power is 250W, built-in power
ONV-P 3 PF 24-Port 10/100/1000M PoE Switch，transmission distance is 100 meter,1-24 port support PoE，IEEE 802.3OE3 024 ： af/at,
the total power is 400W, built-in power
L Angle Iron
Screw
Connect to Power
The Gigabit PoE switch uses AC 100~240V, 50/60Hz power supply
1.Please check if the power supply specification matches with the required;
2.Connect the power cable to AC power socket, shown as in the following pictures
ONV-P 3 PF-at 16-Port 10/100/1000M PoE switch，transmission distance is 100 meter,1-16 port support PoE，IEEE 802.3OE3 016 ： af/at,
the total power is 400W, built-in power
ONV-P 3 PF-at 24-Port 10/100/1000M PoE Switch，transmission distance is 100 meter,1-24 port support PoE，IEEE 802.3 ，OE3 024 ： af/at
the total power is 600W, built-in power
To Previous Page
Loading...
General