P3 International Kill A Watt PS

Need help?

Do you have a question about the P3 International Kill A Watt PS and is the answer not in the manual?

Overview

Function Description
Important Technical Specifications
Usage Features
Maintenance Features

The P4330 Kill A Watt™ PS is a relocatable power tap and transient voltage surge suppressor designed to protect valuable electronics while also monitoring their power consumption. It features a 10-outlet power strip with a spike-free switch and integrated multi-meters to display various electrical parameters.

Function Description

The device serves as both a power strip and a power meter. It provides 10 normal outlets for connecting appliances and incorporates a spike-free ON/OFF switch. The multi-meter functionality allows users to monitor Voltage, Current, Active Power, Power Factor, Kilowatt-Hours (KWH), Leakage Current, and Elapsed Time.

Protection features include:

Abnormal Voltage Protection: Automatically switches off power to the outlets if the input voltage is outside the normal range (under 98.4V or over 135.6V). It will restart automatically when voltage returns to a safe range.
Over Current Protection: Users can set a maximum current limit (2A, 5A, 10A, or 15A) using a switch. If the connected load exceeds this limit, the unit enters Over Current mode, switches off power, flashes a red LED, displays the protected current value, and sounds an audible alarm.
Over Load Protection: Features dual redundant overload protection with an electronic control breaker and a traditional No Fuse Breaker (NFB). If the current load exceeds 15 Amps, the electronic control breaker activates, switching off power, flashing a red LED, displaying the Over Load icon, and sounding an audible alarm. If the NFB detects an overload, it cuts off power to all outlets, LEDs, and the LCD display.
Surge Protection: Built-in circuitry protects against power surges. A "Surge OK" icon indicates proper functioning; its disappearance signals a failed surge protector.
No Load Detection: If all connected appliances are off and drawing no stand-by power (less than 0.2W), the unit automatically turns off power to the outlets, flashes a "NO Load" icon, and turns off the ON key LED. This is a safety feature to de-energize cords.
Ground OK, Wiring OK Detection: Upon connection to a wall outlet, the unit checks for proper Line, Neutral, and Ground wiring. "Ground OK" and "Wire OK" icons display if wiring is correct; their absence indicates a wiring fault.
EMI Filter: Includes a built-in filter to reduce electro-magnetic interference from the AC power line.
Internal Switch Self Test: Flashes a "REPLACE" icon and sounds an audible alarm if the internal relay switch fails.

Important Technical Specifications

Voltage Rating: 120Vrms ± 10%, 60Hz
RMS Voltage Range: 108.0~132.0 Vrms (Accuracy: 0.1% Typ., 0.4% Max.)
RMS Current Range: 0.0~15.0Arms (Accuracy: 0.5% Typ., 1%±0.1A Max.)
Active Power Range: 0.0~1980 Watt (Accuracy: 1% Typ., 2%±5W Max.)
KWH Range: 0.0~9999 KWH (Accuracy: 1% Typ., 2%±5W Max.)
Power Factor Range: 0~100%
Leakage Current Range: 0~30mA (Accuracy: ±1mA)
Elapsed Time Range: 00Day/00Hour~9999Day/23Hour, 00Hour/00Min~23Hour/59Min (Accuracy: 30ppm)
Maximum Output Current: 15A
Over Current Breaker Settings: Programmable 2A, 5A, 10A, 15A
No Load Detector Threshold: Off: <0.2W; On: >0.2W
Surge Protection:
- Maximum Energy Dissipation: 2040 J (L-N, L-G & N-G)
- Maximum Clamping Voltage: 359 V
- Maximum Surge Current: 60000A
- Response Time: <50ns
EMI Filter: Up to 20db for 100K to 20MHz
Power Consumption: 1.0W
Power Cord Length: 1.8m
Dimensions (W/H/D): 320mm x 53mm x 78mm
Weight: 450 g (without power cord)
Operating Environment: Indoor use only, Altitude up to 2000m, Temperature 5°C to 40°C, Maximum relative humidity 80% for temperature up to 31°C decreasing linearly to 50% relative humidity at 40°C.
Mains Supply Voltage Fluctuations: Not to exceed ±10% of the nominal voltage.
Pollution Degree: 2
Installation Category: II

Usage Features

Quick Start Guide:
1. Connect the unit to an outlet and then appliances to the unit.
2. Press any function key to stop the flashing LCD display.
3. Press OFF key (red LED illuminates).
4. Press ON key (green LED illuminates, powers appliances).
5. If no load is detected, the ON key darkens, and "NO Load" icon flashes.
6. Use Volt/Amp key to cycle through Voltage, Current, and Max/Min values.
7. Use Watt/PF key to cycle through Active Power, Power Factor, and Max/Min values.
8. Use KWH/Leakage key to cycle through cumulative KWH, Leakage Current, and Max/Min values.
9. Use Elapsed Time key to cycle through Days:Hours and Hours:Minutes.
Resetting Measurements: Hold the Elapsed Time key for 3 seconds to reset KWH and Elapsed Time measurements to zero. This also clears memorized MAX/MIN values for Voltage, Current, Active Power, Power Factor, and Leakage Current.
Retained Measurements: All accumulated measurements (KWH, Elapsed Time) are retained even if power to the unit is interrupted. The display will flash upon power restoration, indicating an interruption.
Wall Mount: The unit can be optionally wall-mounted using two screws spaced 9 inches (285mm) apart, with screw heads protruding about 1/4 inch (5mm).

Maintenance Features

Cleaning: Unplug the product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.
Servicing: Do not attempt to service the product yourself. Refer all servicing to qualified service personnel.
Damage Requiring Service: Unplug the unit and refer to qualified service personnel if the power-supply cord or plug is damaged, liquid has been spilled, objects have fallen into the product, the product has been exposed to rain or water, the product does not operate normally, the product has been dropped or damaged, or the product exhibits a distinct change in performance.
Replacement Parts: Ensure service technicians use replacement parts specified by the manufacturer or parts with the same characteristics as the original.
Safety Check: After any service or repairs, ask the service technician to perform safety checks.
Troubleshooting Guide: A comprehensive table is provided to diagnose common issues such as flashing LCD, Over Current/Load/Abnormal Voltage icons flashing, No Load icon flashing, "Replace" icon flashing, Ground/Wiring/Surge OK icons off, and no display/response. It suggests actions like pressing keys, checking appliances, resetting the NFB, or contacting technical support.
Warranty: P3 International Corporation offers a limited warranty for six (6) months from the date of purchase, covering defects in material or workmanship under normal use. The warranty does not cover misuse, tampering, neglect, accidents, or unauthorized alterations.