1-5.
MEMORY
STOP
Functions
1.
2.
3.
4.
5.
[liT
5
Press the RESET Button at the
point to
be automatically stopped.
• The tape counter will
be
reset to "0:00:00".
Press the SCREEN DISPLAY
Button.
• The ON-SCREEN
menu
will
be
displayed
on
the
TV
monitor.
Press the OAT A or MEMORY Button.
• Select the "MEMORY STOP" mode.
MEMQRXSl:OP
BGN+O
:
00
:
00
END+O:
00
:
00
'------_j
("
•000""
lamp lights
up
in
the counter.)
Press the SCREEN DISPLAY Button.
• The normal picture will appear.
Press the FF or REW Button.
• When the
FF
or REW Button
is
pressed, the tape will be
wound and then stopped
automatically around the tape
counter position
"0:00:00".
2,4
1
RESET
ME}.10RY
BEGIN
END
~CJ
CJ
CJ
SCREEN
DISPLAY
SHIFT
DOWN
DATA
~CJ
CJ
CJ
SCREEN
DISPLAY
SHIFT
DOWN
DATA
CJ
CJ
CJ
~
or
RESET
MEMORY
BEGIN
END
CJ
~CJ
CJ
SCREEN
DISPLAY
SHIFT
DOWN
DATA
~CJ
CJ
CJ
REW
FF
~
or
~
Notes
• MEMORY STOP function
is
also available by just pressing the MEMORY Button
at
the position except "0:00:00"
after step 1 described above.
• When finished with this function, be sure to select "MEMORY OFF"
in
step 3 described above.
("--+000"
lamp goes
off
in
the counter.)
1-6.
Sensor
Recording (AG-7350 only)
Model AG-7150 is not equipped with recording function.
The unit allows
to
start recording automatically
if
a video input signal
is
supplied to the unit from
an
external source such as a
satellite, etc.
1.
2.
lc=
1---HIE3l
~~~~~======~~~==~~
Turn on the unit and insert a
video cassette.
2
Make sure that the erasure prevention tab
on
the video cas-
sette
is
intact.
Set the SENSOR REC Selector.
In
case of "VIDEO" setting:
• The "SENSOR" indicator will appear
on
the tape counter and
the unit
will
be
set
to
the standby mode. When a video signal
is
inputted into the VIDEO
IN
Connector. the unit
is
turned
on
and set to the recording mode. When there
is
no
more
signal, the unit will go into the stop mode and, after a while,
be
set
to
the standby mode again.
In
case of "REMOTE" setting:
• The "SENSOR" indicator will appear
on
the tape counter and
the unit
will
be
set
to
the standby mode. When a recording
start
signal
is
inputted into the SENSOR REMOTE Connec-
tor
on
the rear panel, the unit
is
turned
on
and set
to
the
recording mode. When a recording end
signal
is
inputted,
the unit
will go into the stop mode and, after a while,
be
set
to
the standby mode again.
• The tape position where
the
SENSOR recording started also
becomes the beginning position
of
the
REPEAT playback.
Similarly,
the
tape position where
the
recording ended
be-
comes the
end
position
of
the
REPEAT playback,
and
the
repeat mode
is
automatically set
to
"REPEAT CONTINUE".
r---·
-----
1
l
___
_
REMOTE~
OFF
E3
VIDEO
SENSOR
RE:
1
Notes
• The "SENSOR" indicator will blink
if
no
video cassette or a video cassette with its erasure prevention tab broken off
is
inserted
in
the unit after the SENSOR REC Selector
is
set "VIDEO" or "REMOTE".
•
When the tape reaches its end during the SENSOR recording, the unit
is
set
to
the stop mode and turned off.
• Any operation buttons are inoperative after the SENSOR
REC
Selector
is
set.
OPERATING INSTRUCTIONS
To Next Page
Loading...
