1-9. Repeat Playback
1.
2.
3.
4.
5.
Press the SCREEN DISPLAY
Button.
• The ON-SCREEN menu will be displayed
on
the
TV
mon~or.
5
Press the DATA or MEMORY Button.
• Select the repeating mode (one-time or continuous repeated
playback mode).
The
"
~
" or
"0"
mark will appear on the tape counter.
Press the DOWN Button.
• Press the SHIFT and DATA Buttons to locate the beginning
and end points of section you wish to perform
REPEAT
playback.
Press the SCREEN DISPLAY Button.
• The normal screen will appear.
Press the FF or REW Button.
• When the tape reaches the beginning BGN points, REPEAT
playback will
start automatically.
1, 4 2
SCREEN
DISPLAY
SHIFT
DOWN
DATA
~Cl
Cl
0
SCREEN
DISPLAY
SHIFT
DOWN
DATA
Cl
Cl
Cl
~
or
RESET
MEMORY
BEGIN
END
Cl
~Cl
CJ
SCRE~N
DISPLAY
SHIFT
Cl
Cl
DOWN
DATA
~0
SCREEN
DISPLAY
SHIFT
DOWN
DATA
~Cl
Cl
0
REW
FF
~
or
~
Notes
• When same data is input for BGN and END, repeat playback is performed from the tape beginning to the end.
• When the data for END has exceeded the tape end, repeat palyback is performed from the BGN position to the
tape end.
• When the data for BGN is smaller than the tape beginning, repeat playback is performed from the tape beginning to
the END position.
OPERATING INSTRUCTIONS
1-10. Time
Code
The SMPTE time code signal recorded onto the tape by using a time code generator/reader permits absolute addressing (the
identification of storage
locations by actual addresses). The time code signal will be recorded on audio CH2 track.
1.
I
w:
1:
I
I
I
ill
I
-~-
~
~
[!j
E1
[!]
0
,toG
·~~11
~~~
ff7.6:·
:O:f6:
8
E1
0
El
··~~
o~~:t):~
~I
_QJ
~
2
Set the selectors.
CH2 METER Selector
AUDIOCH2
(ON-SCREEN)
-+ "CH2" (AG-7350 only) (Refer to page t t
.)
-+
"TIME CODE" (Refer to pages 38 to 40.)
_
....
J I
CJ CJ
CJ
6
t!S
1'5'
~
Cl
o
·e~
_fOl..l
.........
2. When the time code signal has
been entered.
(AG-7350 only)
• The AUDIO CH2 LEVEL meter indicates near 0.
• Time code signals are recorded during recording and dub-
bing
(including audio dubbing
on
channel 2).
Refer
to
the operating instructions of the SMPTE time code
generator/reader you are using for
details.
Connections
re-··--
..
-··-·
..
-·
1@1
<9\§l
3
..
3 u
1
.
-.--:
.
1
111
.....
OIIIOOOI
0
oomm
oomm
o;p-*
OJ)qp
wmoo
mumo
Q'OJS
'"
.,_.
~~--
~ ~
Iii':::::::::
...
~
t:>
~
®
""'""'"
0 0 0
I®
*
Time
Code
Generator
cannot
be
l.U
L.J
connected
to
model
AG-7510.
/
r TIME CODE GENERATOR*
r TIME CODE READER
Note
• The unit's tape counter does not count the time code signals, but the control (CTL) signals recorded onto the tape.
Connect the time code generator/reader to the unit to read the addresses of the time code
signal.
To Next Page
Loading...
