Panasonic AG-7350 Series - (For Ag-7350); Playback Sub Emphasis Input Level Adjustment; Vhs y Playback Level Adjustment (for Ag-7150); Y Playback Level Adjustment (for Ag-7150)

5-3-22. VHS Y PLAYBACK LEVEL ADJUSTMENT
(FOR AG-7150)
TP ADJ.
MODE
INPUT
VIDEO
VR3503
PALVHS
X
OUTPUT 1
PLAY
TAPE M. EQ.
SPEC.
COLOUR
BAR
OSCILLO-
RECORDED
SCOPE
1.0Vp-p±0.02V
TAPE
1. Prepare the normal VHS prerecorded tape which
recorded a colour bar signal on another set
such as AG-7350.
2. Connect the asci lloscope to the video output
with 75ohm termination.
3. Play back the colour bar signal.
4. Adjust VR3502 for 1.0 +/- 0.02Vp-p as shown 1n
Figure E20.
VIDEO OUT 1
(H. RATE)
----- ---~
1.0Vp-p±0.02V
- __ l
with 750 Termination
Figure E20
5-3-23. Y PLAYBACK LEVEL ADJUSTMENT
(FOR AG-7350)
TP
ADJ. MODE
INPUT
VIDEO OUT
1 VR8010
PAL
COLOUR BAR
PLAY
TAPE
M.
EQ. SPEC.
SELF
OSCILLO·
RECORDED
SCOPE
1.0Vp-p
±0.02V
TAPE
Note: This adjustment should be always completed
after the VHS Y playback level adjustment.
1. Supply a colour bar signal to the video input
and record it for a few minute.
2. Play back the just recorded portion.
3. Connect the asci lloscope to the video out
connector with a 75 ohm termination.
4. Adjust VR801 0 for 1.0 +/-0.02Vp-p as shown 1n
Figure E21.
VIDEO OUT 1
(H. RATE)
-------1
1.0Vp-p±0.02V
__ _l
with 750 Termination
Figure E21
5-3-24. Y PLAYBACK LEVEL ADJUSTMENT
(FOR AG-7150)
TP ADJ.
MODE
INPUT
VIDEO OUT
1
VR8010
PAL
X
PLAY
TAPE M. EQ.
SPEC.
COROUR
BAR
OSCILLO-
RECORDED
SCOPE
1.0Vp-p
±0.02V
TAPE
Note: This adjustment should be always completed
after the VHS Y playback level adjustment.
1. Prepare the prerecorded tape which recorded
a colour bar on another recorder (AG-7350).
2. Play back the colour bar signal.
3. Connect the oscilloscope to the video output 1
connector with 75ohm termination.
4. Adjust VR8010 for 1.0Vp-p +/-0.02Vp-p as shown
in Figure E22.
VIDEO OUT 1
(H. RATE)
with 750 Termination
Figure E22
5-3-25. PLAYBACK SUB EMPHASIS INPUT LEVEL
ADJUSTMENT (FOR AG-7350)
TP ADJ. MODE
INPUT
TP3005
VR3001
PAL
COLOUR BAR
PLAY
TAPE
M.
EQ. SPEC.
SELF
OSCILLO-
RECORDED
SCOPE
400mVp-p±10mV
TAPE
Note: This adjustment should be always completed
after completion of all adjustments on the
recording loop.
1. Supply a colour bar signal to the video input
and record it for a few minute.
2. Play back the just recorded portion.
3. Connect the asci lloscope to TP3005.
4. Adjust VR3001 for 400 +/-1 OmVp-p as shown in
Figure E23.
TP3005
(H. RATE)
5-11
----- - --~
400mVp-p ± 10mV
- __ l
Figure E23
....
z
w
::e
....
U)
::l
..,
c
<
..J
<
(.)
a:
....
(.)
w
..J
w