– 153 –
Chapter 7 Menu Operations — Menu list
Item Description of settings
[[S] COLOR CORRECT] Switches the 15-axis independent color correction on/off.
[ON], [OFF]
f Factory setting: [ON]
@@
NOTE
t When saving or reading setup les from an SD memory card, you can save items with an [S] and items without an [S] separately. Items with an [S] in
front of the item name are the targets for [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT]. Items without an [S] are targets
for [PAINT(LEVEL)].
t [−6dB] in [[S] MASTER GAIN] cannot be selected when [NORMAL] is set in main menu → [PAINT] → [[S] CAMERA SETTING] → [SHOOTING
MODE].
t A coloration phenomenon may occur in videos of high-brightness areas if shooting was done with the master gain set to [−6dB] or [−3dB]. After
switching the <OUTPUT>/<AUTO KNEE> selection switch to <CAM>/<OFF> and setting [ON] in the main menu → [PAINT] → [KNEE/LEVEL] → [[S]
MANUAL KNEE], you can reduce the coloration phenomenon by changing the following menu items:
- Reduce the [KNEE MASTER SLOPE] value of [KNEE/LEVEL] when [HD], [SD], [FILMLIKE1], [FILMLIKE2], or [FILMLIKE3] is selected in the main
menu → [PAINT] → [GAMMA] → [GAMMA MODE SEL].
- Reduce the [F-REC DYNAMIC LVL] value of [GAMMA] when [FILM-REC] is selected in main menu → [PAINT] → [GAMMA] → [GAMMA MODE
SEL].
- Reduce the [V-REC KNEE SLOPE] value of [GAMMA] when [VIDEO-REC] is selected in the main menu → [PAINT] → [GAMMA] → [GAMMA MODE
SEL].
[MID SETTING]
Item Description of settings
[[S] MASTER GAIN] Selects the master gain.
[−6dB], [−3dB], [0dB], [3dB], [6dB], [9dB], [12dB], [15dB], [18dB], [21dB], [24dB], [27dB], [30dB]
f Factory setting: [6dB]
[H.DTL LEVEL] Sets the horizontal detail correction level.
[0]…[63]
f Factory setting: [8]
[V.DTL LEVEL] Sets the vertical detail correction level.
[0]…[31]
f Factory setting: [12]
[DTL CORING] Sets the detail noise removal level.
[0]…[60]
f Factory setting: [8]
[H.DTL FREQ.] Selects the horizontal detail frequency.
[0]…[31]
f Factory setting: [18]
[LEVEL DEPEND.] Sets [LEVEL DEPEND.].
Compresses the details of dark areas when Y detail is emphasized.
Details of bright areas are also compressed if the value is large.
[0]…[5]
f Factory setting: [1]
[MASTER GAMMA] Sets the master gamma in 0.01 steps.
[0.30]…[0.75]
f Factory setting: [0.45]
[BLACK GAMMA] Sets the gamma curves of dark areas.
[−8]…[−1]: Compresses the dark areas.
[OFF]: Standard state
[1]…[8]: Expands the dark areas.
f Factory setting: [OFF]
[B. GAMMA RANGE] Sets the maximum level of compression/expansion.
[1]: About 20%
[2]: About 30%
[3]: About 40%
f Factory setting: [1]
[[S] MATRIX TABLE] Selects the color collection table for the linear matrix.
[A], [B], [OFF]
f Factory setting: [A]
[[S] COLOR CORRECT] Switches the 15-axis independent color correction on/off.
[ON], [OFF]
f Factory setting: [ON]
@@
NOTE
t When saving or reading setup les from an SD memory card, you can save items with an [S] and items without an [S] separately. Items with an [S] in
front of the item name are the targets for [PAINT([S]SELECT)] in the main menu → [FILE] → [SETUP DATA SELECT]. Items without an [S] are targets
for [PAINT(LEVEL)].
t [−6dB] in [[S] MASTER GAIN] cannot be selected when [NORMAL] is set in main menu → [PAINT] → [[S] CAMERA SETTING] → [SHOOTING
MODE].
To Next Page
Loading...
