– 229 –
Chapter 9 Network Connection — Network function
- IP address (when the camera’s main menu → [I/F SETUP] → [USB/LAN] → [WIRELESS PROPERTY] → [DHCP SERVER] is set to [ENABLE], IP
address does not need to be set)
Setting for IP connection with the remote operation panel (AK-HRP200G)
You can remotely control some functions by connecting the Remote Operation Panel AK-HRP200G (optional) via IP connection.
To connect the AK-HRP200G via wired LAN to remote-control the camera, congure the settings in the following procedure.
1
Configure the network settings of the camera.
Set the main menu → [I/F SETUP] → [USB/LAN] → [LAN PROPERTY] → [DHCP] to [DISABLE], and refer to steps 1 to 2 in “Wired LAN settings”
(page 225) to congure the network settings.
2
Set the camera’s main menu → [I/F SETUP] → [USB/LAN] → [NETWORK FUNC] → [IP REMOTE] to [ENABLE].
3
Set each item in the camera’s main menu → [I/F SETUP] → [USB/LAN] → [NETWORK FUNC] → [USER ACCOUNT].
[USER NAME]: Sets the user account name. (Factory setting: [guest])
[PASSWORD]: Sets the password. (Factory setting: [p2guest])
Enter up to 31 characters for a user account name, and characters between 6 and 15 for a password.
4
Configure the network settings of the AK-HRP200G.
For the network settings, use ROP setup software that is supplied with AK-HRP200G.
@@
NOTE
t The following information is required to connect to AK-HRP200G.
- User account name
- Password
- IP address
- Port number: 49152
t For AK-HRP200G, use Ver4.01.00 or later versions.
t For details on the operations of ROP setup software, refer to the Operating Instructions of the AK-HRP200G.
t For the ROP setup software, use Ver3.0.0.0 or later versions.
Connection settings for the streaming function
You can perform live streaming of audio and video from the camera over the network (wired LAN, wireless LAN, 4G/LTE).
Streaming can be performed through an application software (e.g. P2 Browser, P2 Streaming Receiver) of a device connected to the camera through a
network, or through a server that is capable of receiving streaming video sent from the camera.
There are two ways to start streaming: streaming from an application software and streaming from the camera. This section describes the camera's
network connection method for each method.
For the procedures on using the streaming function, refer to “Using the streaming function” (page 49).
@@
NOTE
t To display the streaming video in the P2 Browser, start the streaming distribution by operation from the application software. The streaming video
cannot be displayed when operated from the camera.
Setting when starting streaming through operation from an application software
1
Set the connection method when connecting the camera to a network.
Select [WLAN], [4G/LTE], or [LAN] in main menu → [I/F SETUP] → [USB/LAN] → [NETWORK SEL]. For details on each connection method, refer to
“Wireless LAN settings” (page 223) and “Wired LAN settings” (page 225).
@@
NOTE
t [4G/LTE] is disabled when connecting to the P2 Browser.
Setting when starting streaming through operation from the camera
There are two ways to congure the network settings on the camera: conguring the settings from the camera menu or using the settings contained in
the SD memory card.
Conguring the settings from the camera
The followings are the steps to congure the settings from the camera menu.
1
Set the connection method when connecting the camera to a network.
Select [WLAN], [4G/LTE], or [LAN] in main menu → [I/F SETUP] → [USB/LAN] → [NETWORK SEL]. For details on each connection method, refer to
“Wireless LAN settings” (page 223) and “Wired LAN settings” (page 225).
2
Configure the network settings of the camera.
1) Select [INTERNAL] in main menu → [I/F SETUP] → [USB/LAN] → [STREAMING SETTING] → [SETTING DATA].
2) Set each item by matching the connection destinations in main menu → [I/F SETUP] → [USB/LAN] → [STREAMING SETTING].
[SERVER ADDR.]: Sets the IP address of the connection destination.
[RTSP PORT]: Set the RTSP port number of the destination.
To Next Page
Loading...
