Panasonic AJ-PX5000G - Selecting Video Output; Multi Formats

– 57 –
Chapter 4 Adjustments and Settings for Recording — Multi formats
Setting Recording setting (setting menu) Recording/operation enabled/disabled
Operation mode [REC SIGNAL] [REC FUNCTION] Pre-recording One-clip recording
Simultaneous
recording
Interval recording [CAM] [INTERVAL] Not available Not available Not available
One-shot recording [CAM] [ONE SHOT] Not available Not available Not available
Loop recording [CAM] [LOOP] Not available Not available Not available
Standard recording [CAM] [NORMAL] Available Available Available
Input recording of SDI
signal
[SDI] Disabled Not available Not available Available
Setting Recording setting (setting menu) Recording/operation enabled/disabled
Operation mode [REC SIGNAL] [REC FUNCTION] Dual codec recording Text memo Shot mark
Interval recording [CAM] [INTERVAL] Not available Not available Not available
One-shot recording [CAM] [ONE SHOT] Not available Not available Not available
Loop recording [CAM] [LOOP] Not available Not available Not available
Standard recording [CAM] [NORMAL] Available Available Available
Input recording of SDI
signal
[SDI] Disabled Available* Available Available
* It is not available when [LINE&FREQ] is [480-59.94i] or [576-50i].
Selecting video output
The video output method can be selected.
Video output, etc. can be selected by the setting of [OUTPUT SEL] in the main menu → [I/F SETUP] and the setting of [DOWNCON SETTING] →
[DOWNCON MODE].
Menu item Description of settings
[SDI2/HDMI OUT]
Selects the system mode signal method or down converter output for output from the <SDI
OUT2> and <HDMI OUT> terminals.
[1080P SDI2/HDMI OUT]
Selects whether to convert output signals from the monitor output terminals (<SDI OUT2>,
<HDMI OUT>) to 1080i at 1080P.
[3G-SDI OUT]
Selects the 3G-HD SDI signal type output from the <SDI OUT1> and <SDI OUT2> terminals
from [LEVEL-A] or [LEVEL-B] at 1080P.
[DOWNCON MODE]
Selects the screen type for down-conversion output (composite and SD SDI output) at 1080P,
1080i, or 720P.
Selecting video output from each terminal
[LINE&FREQ]
Monitor output setting Video output
[SDI2/HDMI
OUT]
[1080P SDI2/
HDMI OUT]
<SDI OUT1> terminal <SDI OUT2> terminal <HDMI OUT> terminal
<VIDEO OUT>
terminal
[1080-59.94P]
[SYSTEM
MODE]
[1080P]
1080/59.94P*
1080/59.94P* 1080/59.94P
480/59.94i[1080i] 1080/59.94i 1080/59.94i
[DOWNCON] Disabled 480/59.94i 480/59.94P
[1080-50P]
[SYSTEM
MODE]
[1080P]
1080/50P*
1080/50P* 1080/50P
576/50i[1080i] 1080/50i 1080/50i
[DOWNCON] Disabled 576/50i 576/50P
[1080-59.94i]
[SYSTEM
MODE]
— 1080/59.94i
1080/59.94i 1080/59.94i
480/59.94i
[DOWNCON] 480/59.94i 480/59.94P
[1080-50i]
[SYSTEM
MODE]
— 1080/50i
1080/50i 1080/50i
576/50i
[DOWNCON] 576/50i 576/50P
[1080-23.98PsF]
[SYSTEM
MODE]
[1080P]
1080/23.98PsF*
1080/59.94P* 1080/59.94P
480/59.94i[1080i] 1080/59.94i 1080/59.94i
[DOWNCON] Disabled 480/59.94i 480/59.94i
[720-59.94P]
[SYSTEM
MODE]
— 720/59.94P
720/59.94P 720/59.94P
480/59.94i
[DOWNCON] 480/59.94i 480/59.94i
[720-50P]
[SYSTEM
MODE]
— 720/50P
720/50P 720/50P
576/50i
[DOWNCON] 576/50i 576/50P
[480-59.94i] — — 480/59.94i 480/59.94i 480/59.94P 480/59.94i
[576-50i] — — 576/50i 576/50i 576/50P 576/50i
* Output type can be selected from [LEVEL-A] or [LEVEL-B] in the main menu → [I/F SETUP] → [OUTPUT SEL] → [3G-SDI OUT]. This item is set to [LEVEL-B] in
the factory setting.