Panasonic AJ-PX5000G - Selecting Display Items on Viewfinder Screen; Screen Display

– 83 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
Selecting display items on viewnder screen
To select display items on the viewnder screen, switch [ON]/[OFF] or the type of the respective item in the main menu → [VF] → [VF INDICATOR].
For details, refer to “Setting menu basic operations” (page 147).
Screen display
A V C - I 1 0 0 R E mP2 1C
E A MS T R
RP- E C
5 9 9 min
min
s
1 4 .6 V
2 1 9 9 C A C
F B C
H.S EN S.
SD
ERRPROXY
1 9 9 min
U 2 : S . G A I N 3 0 dB A T W L O C K
M K R : O F F
S Y S T E M E R R O R E - 3 4 F R E C
DZ
EX
X 4 < L C D M I C O N >
D R S T C G 0 0 : 0 0 : 0 0 : 0 0 8
1 5 K 1 2 F : 1 S B M F 2 3 .5 m
1 A A 1 8 dB
6 5 %
F : 2 F 5. 6 Z 5 6 .9 mm
6 0 i
1/ 7 2
.00
1 0 8 0 5 9 .9 4 i
C O M P
SIMUL
SDI REC
W L A N
!
I P R E M O T E
1
13 15
17
14
25
2
4
3
5
6
7
8
9
10
11
12
45 4446 43 42 41 40 39 38
19 20 22 24
16
18
21 23
26
27
28
29
30
31
32
33
35
34
36
37
1 Shutter speed/mode
[w1/**.*]
The shutter speed is set to synchro scan.
[1/60 (1/100)] - [1/2000],
[HALF], [***.*d]
A xed shutter speed is set.
2 Camera mode
Displays the video method when the signals output from the MOS sensor are recorded to the P2 card or output as video signals.
[60P] 1080/59.94P or 720/59.94P
[60i] 1080/59.94i or 480/59.94i
[50P] 1080/50P or 720/50P
[50i] 1080/50i or 576/50i
[30P] 1080/29.97P or 720/29.97P
[24P] 1080/23.98P, 1080/23.98PsF or 720/23.98P
[25P] 1080/25P or 720/25P
3 HD SDI recording control information and 4G/LTE connection status display
This is displayed against the HD SDI signal of the <SDI OUT1> or the <SDI OUT2> terminals when the [HDSDI REMOTE] in the main menu → [I/F
SETUP] → [OUTPUT SEL] is set to [ON], and the recording control information is superimposed. It is not displayed when [HDSDI REMOTE] is set to
[OFF].
[SDI REC] Recording instruction is being output.
[SDI&]
Recording standby instruction is being output.
Displays the 4G/LTE connection status.
Displays the following when connected to 4G/LTE. The signal reception strength is displayed in 6 levels. The number of vertical bars represent the
signal strength. Not displayed when the 4G/LTE setting is disabled.
[4G/LTE ]
Displayed when connected to 4G/LTE.
[4G/LTE
]
Displayed when not connected to 4G/LTE.
[4G/LTE
]
Displayed when there is an error in the 4G/LTE connection.
@@
NOTE
t Depending on the 4G/LTE USB modem that is supported, vertical bars that indicate the signal strength may not be displayed.