– 84 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
4 Proxy information display
Displays the proxy recording information.
[PROXY P2 (P2&SD)] Displayed when proxy recording is started.
[PROXY ERR] Displayed when there is an error in proxy recording.
5 SD memory card status display
[WP] Write protect
[END] No remaining free space
[WR ERR] Write error
[SD ***min]
The remaining amount is displayed when proxy is recorded to SD memory card. (Displayed only in the regular mode check)
Flashing when the remaining capacity is one minute or less. [−−min] is displayed when there is no SD memory card.
6 Camera warning, notication display area
(Related to automatic white balance, automatic black balance and switch operation)
[AWB A ACTIVE] Displayed when automatic white balance is active on the <A> channel.
[AWB B ACTIVE] Displayed when automatic white balance is active on the <B> channel.
[AWB A OK *.*K]
Displayed when automatic white balance has ended successfully on the <A> channel.
[AWB B OK *.*K]
Displayed when automatic white balance has ended successfully on the <B> channel.
[AWB BREAK *.*K]
Displayed when automatic white balance operation is forcibly ended.
[AWB NG]
Displayed when automatic white balance operation is not ended successfully. The 2nd line displays that status.
[COLOR TEMP LOW] Warns that the color temperature is too low.
[COLOR TEMP HIGH] Warns that the color temperature is too high.
[LEVEL OVER] Warns that the brightness is too high.
[LOW LIGHT] Warns that the brightness is too low.
[TIME OVER] Warns that processing could not be executed within the operation time.
[ATW MODE] Displayed when automatic white balance cannot be executed due to activation of auto tracking white balance.
[AWB PRESET *.*K]
Displayed when the <WHITE BAL> switch is set to <PRST> and automatic white balance operation cannot be executed.
[AWB UNABLE]
Displayed when automatic white balance operation cannot be executed. The 2nd line displays that status.
[S.GAIN MODE] Displayed when super gain is active.
[CHECK FILTER] Prompts re-conrmation of the lter switching dial position when the power is turned on and automatic white balance is active.
[ABB ACTIVE] Displayed when automatic black balance operation is active.
[ABB OK] Displayed when automatic black balance operation is ended successfully.
[ABB BREAK] Displayed when automatic black balance operation is forcibly ended.
[ABB NG] Displayed when automatic black balance operation is not ended successfully.
[B-SHD READY]
Displayed when black shading operation is accepted by holding down the <AUTO W/B BAL> switch during automatic black
balance operation.
[B-SHD ACTIVE] Displayed when black shading operation is active.
[B-SHD OK] Displayed when black shading operation is ended.
[B-SHD BREAK] Displayed when black shading operation is forcibly ended.
[B-SHD NG] Displayed when black shading operation is not ended successfully.
(Switch selection display)
[WHITE:#]
Displayed when the <WHITE BAL> switch is switched. One of [A]/[B]/[PRST] is displayed at [#].
[ATW MODE] Displayed when automatic tracking white balance operation is set.
[*.*K]
Displays the currently set color temperature.
[AUTO KNEE:ON/OFF]
Displayed when the <OUTPUT>/<AUTO KNEE> selector switch where [ON] or [OFF] is assigned in the main menu →
[CAMERA] → [SW MODE] → [AUTO KNEE SW] is set to <ON>/<OFF>.
[DRS:ON/OFF]
Displayed when the <OUTPUT>/<AUTO KNEE> selector switch where [DRS] is assigned in the main menu → [CAMERA] →
[SW MODE] → [AUTO KNEE SW] is set to <ON>/<OFF>.
[GAIN:**dB+**↑]
Displayed when gain is switched by the <GAIN> switch or <USER> button. When digital super gain is active, that value is
displayed at the same time.
[SS:1/****] or
[***.*deg]
When the shutter speed is switched, that value is displayed.
[SS: w 1/****] or
[w***.*d]
Displayed when syncro scan is selected for the shutter speed.
[CC:**** **K]
Displayed when the <CC FILTER> dial position is switched.
[ND:*]
Displayed when the <ND FILTER> dial position is switched.
[EXTENDER:ON/OFF] Displays the status of the lens extender.
[IRIS:**F*.*]
Displayed when the iris override compensation value is altered.
(Drop in brightness warning display)
[LOW LIGHT] Displayed when brightness has dropped.
(Flash band compensation warning display)
[FBC OFF!] Displayed when a ash band is detected while ash band compensation is off.
[SHUTTER&FBC ON!] Displayed when the <SHUTTER> switch is <ON> and ash band compensation is set to on.
To Next Page
Loading...
