– 88 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
[STREAM] Displays when the streaming function is set and can be operated normally.
[STRM
]
Displays when there is an error, and cannot operate normally. To restore, turn off the power once and turn on the power again.
32 Y GET brightness display
In the Y GET mode, the image level in the frame displayed near the center of the screen is displayed as 0% to 109%.
33 Remote control display in an IP connection
Displays the remote control status in an IP connection when [IP REMOTE] is set to [ENABLE] in the main menu → [I/F SETUP] → [USB/LAN] →
[NETWORK FUNC].
[IP REMOTE] (ashing) Displayed during connection waiting status in an IP connection.
[IP REMOTE]
(illuminated)
Displayed when remote control is possible in an IP connection.
34 Compression mode
When the recording format is DVCPRO HD in 720P, displayed if the camera is set to the mode in which distortions in a compressed video generated
due to lming dark areas are reduced.
35 High-sensitivity mode display
Displayed when set [HIGH SENS.] in the main menu → [PAINT] → [[S] CAMERA SETTING] → [SHOOTING MODE].
36 Flash band compensation (FBC) function display
Displayed when the ash band compensation function is activated.
37 Chromatic aberration compensation
[CAC] Displayed when the chromatic aberration compensation function is active.
38 Battery charge level/voltage
[**.*V]
Displays the battery charge level in 0.1 V units.
[***%]
Displays the charge level of batteries with charge level information in %.
[EMP] Displayed when there is no charge level on batteries with charge level information or the level is at the near end setting value or
below.
[MAX] Displayed when batteries with charge level information are fully charged.
39 P2 card remaining free space
This is the slot No. This is displayed in black and white inversion when the slot No. is recording destination. It ashes while the
card is being recognized.
[***min]
Displays the remaining space on the media in each slot. During a near end, it ashes.
0 to 599 indicates minutes, while 600 minutes or longer indicates hours.
(No display) Not displayed when a card is not inserted.
[END] Displayed when there is no space remaining on each card.
[WP] Displayed when the P2 card is write-protected.
[ERR] Displayed in the case of format errors or authentication errors.
[LOOP ***min]
Displayed when the loop recording mode is set. During the mode check, the 2nd line displayed the standard recording time of
loop recording.
[LOOP] ashes when loop recording is not possible, for example, when there is no more space remaining on the P2 card.
40 Simultaneous recording mode display
[SIMUL] Displayed when the simultaneous recording is set.
When the simultaneous recording cannot be performed, [SIMUL] indication is displayed with a diagonal line.
41 Recording media display
Among P2 and microP2 memory card slots, displays the slot that can perform recording and playback operations set in the main menu → [REC/PB]
→ [REC/PB SETUP] → [REC MEDIA].
[P2] P2 memory card slot
[mP2] microP2 memory card slot
42 Rec during upload function status display
Displays the status of rec during upload.
[ ]
Displays when the rec during upload function is enabled.
The display will ash immediately after the power is turned on or the P2 card is inserted, and the upload will not be executed until
the recording is stopped.
[
]
Displayed during upload.
[
]
Displayed from when transfer error occurred during upload until when the next upload starts.
43 Recording operation status display
[REC]
Displayed when set [CHAR] in the main menu → [REC/PB] → [REC/PB SETUP] → [REC TALLY]. This is also displayed when
set [ON] in the main menu → [VF] → [VF INDICATOR] → [REC STATUS].
44 Streaming distribution status display
Displays the streaming status.
To Next Page
Loading...
