– 91 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
Mode check display
The camera settings and status can be displayed on the viewnder screen.
Pushing the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch on the camera towards the <MCK/MCL> side switches the six screens.
[STATUS] screen display → [!LED] screen display → [FUNCTION] screen display → [AUDIO] screen display → [CAC] screen display → [USER SW
STATUS] screen display → no display
Each screen is displayed for approximately ve seconds. Pushing the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch towards the <MCK/
MCL> side while the screen is displayed moves the display to the next screen. [ON]/[OFF] of each screen display can be selected in the main menu →
[VF] → [MODE CHECK IND]. For details on [STATUS] screen displays, refer to “Checking and displaying shooting status” (page 89).
[!LED] screen
Displays items that are causes of [!LED] lighting.
f [!] is attached to items currently selected at [!LED].
f
is attached to items currently targeted for [!LED] lighting.
[GAIN(0dB)] Displays the gain status.
[DS.GAIN] Displays the digital super gain value.
[SHUTTER] Displays the shutter status.
[WHITE PRE.] Displays the white balance status.
[EXTENDER] Displays the extender status by [EX]/[OFF].
[B.GAMMA] Displays the black gamma status by [ON]/[OFF].
[MATRIX] Displays the [MATRIX] status by [A]/[B]/[OFF].
[COLOR COR.] Displays the [COLOR CORRECTION] status by [ON]/[OFF].
[FILTER] Displays the lter status.
[ATW] Displays the status of automatic tracking white balance.
[FUNCTION] screen
Displays the video output status and information of the recording media.
[SDI OUT1] — Displays the status of the signal output from the <SDI OUT1> terminal.
[OUTPUT]
Displays the status of [MEM]/[CAM] or [OFF] set by [SDI OUT1] and [SDI OUT1 MODE] in
the main menu → [I/F SETUP] → [OUTPUT SEL].
[TYPE]
Displays the format of the signal output from the <SDI OUT1> terminal by [HD-SDI]/
[SD-SDI].
[CHAR]
Displays the superimposition status of characters selected in the main menu → [I/F
SETUP] → [OUTPUT SEL] → [SDI OUT1 CHAR] by [ON]/[OFF].
[SDI OUT2] — Displays the status of the signal output from the <SDI OUT2> terminal.
[OUTPUT]
Displays the status of [MEM]/[CAM] or [OFF] set by [SDI OUT2] and [MONITOR OUT
MODE] in the main menu → [I/F SETUP] → [OUTPUT SEL].
[SELECT]
Displays the signal format set by [SDI2/HDMI OUT] and [1080P SDI2/HDMI OUT] in the
main menu → [I/F SETUP] → [OUTPUT SEL] by [SYSTEM]/[DOWNCON]/[1080i].
[CHAR] Displays the position of the <MON OUT CHARATER> switch by [ON]/[OFF].
[P2CARD STATUS]
—
Displays the status of the P2 card inserted in the card slot, remaining capacity and total
used capacity.
The statuses of cards to be displayed are as follows:
[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/
[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]
For details, refer to “P2 card access LEDs and status of P2 cards” (page 32).
[TOTAL P2/mP2]
Displays the remaining capacity/total capacity totaled for slots 1/2 (or slots 3/4) and the
recording medium ([P2] or [mP2]).
[SLOT1] or [SLOT3] Displays the status of the P2 card in slot 1 (or slot 3) and remaining capacity/total capacity.
[SLOT2] or [SLOT4] Displays the status of the P2 card in slot 2 (or slot 4) and remaining capacity/total capacity.
[PROXY]
[MEDIA]
Displays the media selection status for proxy recording.
[P2]/[P2&SD]/[OFF]
[MODE]
Displays the setting status for proxy recording mode.
[STD 2CH MP4]/[SHQ 2CH MOV]/[HQ 4CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV]/
[AVC-G6 2CH]
[SUPER]
Displays the superimposed setting status of the time code.
[UPPER]/[LOWER]/[OFF]
[PROXY ERROR] Displays the operation error on the proxy module.
[NETWORK] [NETWORK] Displays the network to be used and its status.
[AUDIO] screen
Displays audio settings and the selection status of each recording channel.
[SAMPLE RES] — Displays the number of audio recording bits.
To Next Page
Loading...
