Panasonic AJ-PX5000G - Setting the Marker Display; Display of Marker Confirmation Screen (Marker Select Function); Confirmation of Return Video Signal in the Viewfinder; Zebra Patterns Display

– 93 –
Chapter 4 Adjustments and Settings for Recording — Viewnder status display
Status for displaying messages Message
[DISP MODE] setting
[1] [2] [3]
When the <WHITE BAL> switch setting is changed
[WHITE:n]
([n] = [A], [B], [PRE])
— —
l
When the <OUTPUT>/<AUTO KNEE> selector switch is set to
<ON> or <OFF>
[AUTO KNEE:ON] (or [OFF]) —
l l
When the shutter speed/mode setting is changed
[SS:1/100]
(or [1/60], [1/120], [1/250], [1/500],
[1/1000], [1/2000], [HALF], [***.*d], [w1/**.*] or
[w***.*d])
—
l l
When white balance is adjusted Example) [AWB A OK 3.2 K] —
l l
When black balance is adjusted Example) [ABB OK] —
l l
When the extender is selected Example) [EXTENDER ON] — —
l
When the <USER> button is selected Example) [UM:S.GAIN 30dB] —
l l
When the marker select function is selected Example) [MKR:A] — —
l
When in the iris override mode
Example) [++F5.6]
—
l l
When the CAC lens is mounted or unmounted Example) [CAC LENS DATA INVALID] —
l l
Setting the marker display
Select the type and display of the center marker, safety zone marker, safety zone area, and frame marker. Select the display mode of each item in the
main menu → [VF] → [VF MARKER].
Display of marker conrmation screen (marker select function)
The screen for conrming the marker status of the camera can be displayed on the viewnder screen.
Type of marker
Center marker
Safety zone
The aspect ratio currently set at [FRAME SIG] is displayed.
Pushing the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch on the camera towards the <MKR> side switches between [A] marker display
→ [B] marker display → no display
With the following settings in advance, you can check the angle of view at 14:9 and 4:3 easily by this button, if necessary. As the [A] marker information,
set [14:9] in the main menu → [VF] → [VF MARKER] → [FRAME SIG], and as the [B] marker information, set [4:3] in [FRAME SIG].
Conrmation of return video signal in the viewnder
The return video signal input to the <SDI IN> terminal can be viewed in the viewnder while the <RET> button on the lens is held down. To activate this
function, select [CAM RET] in the main menu → [CAMERA] → [SW MODE] → [RET SW].
@@
NOTE
t The HD-Y or VBS signals of the <GENLOCK IN> terminal cannot be viewed as return video signals.
Zebra patterns display
The camera can display two types of zebra patterns.
When the <ZEBRA> switch of the viewnder is set to <ON>, the zebra pattern currently set in the menu is displayed on the viewnder screen.
Zebra patterns can also be displayed in the video of the monitor output terminal (<SDI OUT2>, <VIDEO OUT>, <HDMI OUT>) according to settings.
The level for displaying zebra patterns can be set in the main menu → [VF] → [VF DISPLAY].
Item Setting value Description of settings
[ZEBRA1 DETECT]
[0%]…[70%]…[109%] Sets the level of zebra pattern 1 tilting to the right.
[ZEBRA2 DETECT]
[0%]…[85%]…[109%] Sets the level of zebra pattern 2 tilting to the left.
[ZEBRA2]
[ON], [SPOT], [OFF] Selects the type of [ZEBRA2].
are factory settings.
[SPOT]: The image level from the setting value of [ZEBRA1 DETECT] to the setting value of [ZEBRA2 DETECT] is displayed in the zebra pattern.