Panasonic AK-HC3900G - [System Mode]; [In;Out Select]

– 60 –
Chapter 4 Menu Operations — Menu list
[SYSTEM MODE]
[FORMAT] cannot be selected right after the power is turned on, because boot of the camera is in progress.
This is not an error. Perform operation after a while.
Item Description of settings
[FORMAT] Sets the system format.
[2160/59.94p], [2160/29.97p], [2160/23.98p], [1080/59.94p], [1080/29.97p], [1080/23.98p], [2160/50p],
[2160/25p], [1080/50p], [1080/25p]
 Factory setting: [1080/59.94p]
[COLORIMETRY]
Change the Y/C conversion coefcient.
[BT.709], [BT.2020]
 Factory setting: [BT.709]
NOTE
 Fixed to [BT.709] when [FORMAT] is other than [2160].
 The outputs of HD-SDI 1 and 2 become [BT.709] when each [HDR SW] is [OFF].
[GAMUT] Change the color gamut.
[NORMAL], [WIDE_G]
 Factory setting: [NORMAL]
NOTE
 Fixed to [NORMAL] when [FORMAT] is other than [2160].
 The outputs of HD-SDI 1 and 2 are xed to [NORMAL].
[HDR SW] — Enables/disables the HDR mode.
[OFF], [ON]
 Factory setting: [OFF]
[HD_SDI1 OUT(HDR)] Enables/disables the HDR signal from the <HD SDI1> terminal.
[OFF], [ON]
 Factory setting: [OFF]
[HD_SDI2 OUT(HDR)] Enables/disables the HDR signal from the <HD SDI2> terminal.
[OFF], [ON]
 Factory setting: [OFF]
[SHOOTING MODE]
Sets the shooting mode.
[NORMAL], [HIGH SENS]
 Factory setting: [NORMAL]
[CABLE CONNECTION]
Set the connection method used between the camera and CCU.
[HYBRID], [FIBER]
 Factory setting: [HYBRID]
[IN/OUT SELECT]
Item Description of settings
[CALL TALLY]
Sets whether the rear tally lamp is to be lit up when called.
[OFF]: Turned off.
[R]: Red tally lights up.
[T]: Up tally lights up.
[R&T]: Red tally and up tally light up.
 Factory setting: [OFF]
[TALLY GUARD]
Enables/disables automatic white balance, automatic black balance, and automatic setup when the tally lamp is lit.
[OFF], [ON]
 Factory setting: [OFF]
[HD-SDI1 OUT]
Congures the video output from the <HD SDI1> terminal.
[CAM]: Outputs camera images.
[HD PROMPT]: Outputs HD prompter video images.
 Factory setting: [CAM]
[HD-SDI1 OUTPUT FORMAT]
Sets the signal format of the video output from the <HD SDI1> terminal.
[1080i], [1080P], [720P]
 Factory setting: [1080i]
[HD-SDI1 OUTPUT ITEM]
Selects details of the characters superimposed on images output from the <HD SDI1> terminal.
[MENU ONLY]: Displays only on the menu.
[STATUS]: Displays all characters that are the same as in the viewnder display.
 Factory setting: [MENU ONLY]
[HD-SDI1 CHAR]
Sets whether to superimpose characters on images output from the <HD SDI1> terminal.
This cannot be set when the output format is [720P].
[OFF], [ON]
 Factory setting: [OFF]
[HD-SDI1 CHAR SIZE]
Sets the size of the characters superimposed on images output from the <HD SDI1> terminal.
[LARGE], [SMALL]
 Factory setting: [SMALL]