60 Aquarea air-to-water heat pumps - Planning and installation manual - 02/2022
Product Description
4
domestic hot water tank this function is available only after the external domestic water temperature
sensor is installed, electrically connected and enabled via the remote controller.)
!
IMPORTANT
As it is not possible to cover all variants of remote controller functions for all models within the
scope of this manual, only the most recent remote controller for the J generation and its functions
are explained in detail to serve as an example.
However, not all functions stated here will be available for all models. Therefore, in order to be
sure about the valid functions of each model, it is absolutely mandatory to refer to the operating
instructions or service manual for the relevant model when operating the device.
4.7.1.1 Remote controller for J and H generation models
The remote controller is in the scope of delivery of the following models:
Bi‑bloc systems with All in One unit Bi‑bloc systems with hydrokit Mono‑bloc systems
High Performance | J Generation | R32 High Performance | J Generation | R32 High Performance | J Generation | R32
WH-ADC0309J3E5+WH-UD**JE5(-1) WH-SDC**J3E5+WH-UD**JE5(-1) WH-MDC**J3E5
WH-ADC0309J3E5B+WH-UD**JE5(-1) High Performance | H Generation | R410A High Performance | H Generation | R410A
WH-ADC0309J3E5C+WH-UD**JE5(-1) WH-SDC**H6E5+WH-UD**HE5 WH-MDC**H6E5
High Performance | H Generation | R410A WH-SDC**H3E8+WH-UD**HE8 T‑CAP | J Generation | R32
WH-ADC1216H6E5+WH-UD**HE5 T‑CAP | H Generation | R410A WH-MXC**J3E5
WH-ADC0916H9E8+WH-UD**HE8 WH-SXC**H3E5+WH-UX**HE5 WH-MXC**J3E8
T‑CAP | H Generation | R410A WH-SXC**H3E8+WH-UX**HE8 T‑CAP | H Generation | R410A
WH-ADC1216H6E5+WH-UX**HE5 WH-SQC**H3E8+WH-UQ**HE8 WH-MXC**H3E5
WH-ADC1216H6E5C+WH-UX**HE5 WH-MXC**H3E8
WH-ADC0916H9E8+WH-UX**HE8
WH-ADC0916H9E8+WH-UQ**HE8
4.7.1.2 Design and functions of the remote controller
A
B
1 5
6
2 3
7
4
Basic Functions
A Display
Graphic, background-illuminated LCD display with easily understandable symbols as well as plain text menu dis-
plays in 10 different user languages.
1 Operating mode
Display of the set operating mode or of the current operating mode:
16.07.2021, cH
By comparing the Service Manuals for WH-ADC-
0309J3E5 and WH-ADC1216H6E5, I have identified
the following functions to be new on the J gener-
ation controller as compared to the H generation
controller. Is my list (see below) complete and
correct, or am I missing something?
[#22.07.2021, M.Serrano]
- Room thermistor as new “Sensor type/Set tem-
perature type”
[#This has not actually changed. “Room thermis-
tor” was already available for H Series.]
- New function for setting tank sensor to “Top” or
“Center”
[#OK.]; cH: added (11.11.2021)
- “Water temperatures” is now named “System
information”, with “COMP frequency” and “Pump
flowrate” as additional entries
[#OK.]; cH: added (11.11.2021)
- Two new display languages: Turkish, Finnish
[#OK. Additionally we have included Lithuanian
and Portuguese, but it’s not yet reflected in all
manuals.]
- New function “DHW capacity (Variable/Standard)”
[#OK.]; cH: added (11.11.2021)
- New function for setting “Bivalent connection” to
“Auto” or “SG ready” control pattern; and if “SG
ready” is chosen, there are new specific SG ready
settings
[#OK. Additionally also now Smart Grid ready (SG) is
available for Cooling]; cH: added (11.11.2021)
- New function “Force defrost”
[#This we already had in H]; cH: not in old manual,
added (11.11.2021)
- New function “Defrost signal”
[#OK.]; cH: added (11.11.2021)
- New function “Pump flowrate”
[#OK.]; cH: added (11.11.2021)
12.11.2021, cH
In order not to miss any deviations of the H gen.
compared to the J gen. (so to be on the safe side),
I changed the wording to limit this function over-
view to the J gen. models ONLY. OK? (You know,
the lazy ones are usually the smart ones, too. ;-))
To Next Page
Loading...
