Operating Instructions
17. AUDIO IN connector <AUDIO INPUT 1, 2>
Inputs external audio (microphone, line).
AUDIO INPUT 1, 2
12
3
1 GND
2 AUDIO IN (H)
3 AUDIO IN (C)
18. 3G SDI OUT connector <3G SDI OUT 1, 2/PM>
This is an SDI video signal output connector. Depending upon the
output signal format, 3G‑SDI or 1.5G‑SDI signals are output.
When using SMPTE ST2110, if images are input to SFP+, then the
images input as RETURN signals can be output as from 3G SDI
OUT2/PM.
<NOTE>
• A separate optional software key (AW‑SFU60) needs to be
purchased to enable SMPTE ST2110 functionality.
19. Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. (→ page 27)
20. G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri‑level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Frequency: 119.88 Hz
Format
External sync signal input format
Tri-level sync BBS
1080/119.88p
― ―
1080/59.94i
1080/29.97PsF
480/59.94i
Frequency: 100 Hz
Format
External sync signal input format
Tri-level sync BBS
1080/100p
― ―
1080/50i
1080/25PsF
576/50i
Frequency: 60 Hz
Format
External sync signal input format
Tri-level sync BBS
1080/60p 1080/60p
― ― ―
Frequency: 59.94 Hz, 29.97 Hz
Format
External sync signal input format
Tri-level sync BBS
2160/59.94p
― ―
1080/59.94i
1080/29.97PsF
480/59.94i
2160/29.97p
1080/59.94p
1080/29.97p
720/59.94p
―
720/59.94p
―
Frequency: 50 Hz, 25 Hz
Format
External sync signal input format
Tri-level sync BBS
2160/50p
― ―
1080/50i
1080/25PsF
576/50i
2160/25p
1080/50p
1080/25p
720/50p
―
720/50p
―
Frequency: 24 Hz
Format
External sync signal input format
Tri-level sync BBS
2160/24p 1080/24p 1080/24PsF
― ―
1080/24p
Frequency: 23.98 Hz
Format
External sync signal input format
Tri-level sync BBS
2160/23.98p 1080/23.98p
1080/23.98PsF
― ―
1080/23.98p
21. RS-422 connector <RS-422>
This RS‑422 connector (RJ‑45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
Furthermore, by shorting the R‑TALLY signal (2‑pin) with the GND
(1‑pin), it is possible to light the tally lamp (red) in the camera head
section of the unit.
<NOTE>
• Do not connect PoE cable to the RS‑422 port.
• Do not apply a voltage to the R_TALLY_IN signal pin.
• Menu settings enable the output to pin 7 and pin 8 of the red tally
and green tally signals received by the unit. Output is by contact
output, and normally is “OPEN”, then it becomes “MAKE” for
output. (Operating Instructions (PDF) → “Camera menu items”
→ “OUTPUT” → “EXTERNAL OUTPUT”)
LAN cable
*
1
(category 5e or above, straight cable),
max. 1000 m (3280 ft)
*
1
Use of an STP (shielded twisted pair) cable is recommended.
Pin
No.
Signal
Pin
No.
Signal
1 GND 5 TXD+
2 R_TALLY_IN 6 RXD+
3 RXD– 7
OPTION_OUT1
4 TXD– 8
OPTION_OUT2
Example OPTION_OUT1, OPTION_OUT2 connector
connections
AW-UE160
OPTION_OUT1
OPTION_OUT2
GND
Voltage: Maximum DC12 V
Current: Maximum 100 mA
36 37
Parts and their functions (continued)
To Next Page
Loading...
