Bar [Camera, Colorbar]
Switch between camera images and color bars.
Camera Camera images
Colorbar Color bar
Factory settings: Camera
Color Bar Type [Type1, Type2]
Select the type of color bar to display.
Type1:
Type2:
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Type2
Tone [Off, Low, Normal]
Make the settings for the test tone signal (1 kHz) output while the
color bar is displayed.
Off Test tone is not output.
Low Test tone is output at low volume.
Normal Test tone is output at normal volume.
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Normal
OSD Mix
Selects whether to turn Off/On display of camera menu and status.
3G SDI [Off, On
*
] (AW‑UE50 only)
Selects whether to turn this Off/On for images output from 3G SDI
OUT connector.
HDMI [Off, On
*
]
Selects whether to turn this Off/On for images output from HDMI
connector.
IP/NDI|HX [Off, On
*
]
Selects whether to turn this Off/On for images other than NDI images
(H.264/H.265/JPEG/RTMP/SRT/NDI|HX) output from the LAN
connector.
Off The camera menus and statuses are not displayed on the
output pictures covered by the setting items listed above.
On The camera menus and statuses are displayed on the
output pictures covered by the setting items listed above.
*
: Factory settings
<NOTE>
• When this is set to [Off], the camera menu can be displayed for
about 1 minute after the unit is turned on.
OSD Off With R‑Tally [Off, On]
Off or on the function that turns off camera menu, status and other
displays when red tally signals are received via commands or
contacts.
When the red tally signal releases, the camera menu display will
return.
Factory settings: Off
OSD Status [Off, On]
Turn the status display during AWB and ABB off/on, or error display
when an error occurs.
Factory settings: Off
Tally [Disable, Enable]
[Disable] or [Enable] is set here for the function which turns on or
turns off the tally lamp using the tally control signal.
Factory settings: Enable
Tally LED Limit
Sets whether to limit the lighting of the tally lamp for each of the tally
control signal colors (R/G/B).
R [Limit, Unlimit
*
]
G [Limit, Unlimit
*
]
B [Limit, Unlimit
*
]
Limit Limit the lighting of the tally lamp.
Unlimit Light the tally lamp.
*
: Factory settings
<NOTE>
• If [Disable] is selected for [Tally], the tally status display on external
devices (the web screen, controllers such as AW-RP150 and
AW-RP60) is also disabled along with the limiting of the tally lamp
lighting on this unit.
• If [Limit] is selected for [Tally LED Limit], only lighting of the tally
lamp of this unit is limited. The tally status display on external
devices (the web screen, controllers such as AW-RP150 and AW-
RP60) remains enabled.
Tally Brightness [Low, Mid, High]
Adjust the brightness of the tally LED.
Factory settings: Low
Status Lamp [Disable, Enable]
[Disable] or [Enable] is set here for the status display lamp.
When you want the status display lamp to stay off while this unit is in
operation, set to [Disable].
Factory settings: Enable
<NOTE>
• Even when set to [Disable], the status display lamp may light
up when this unit is starting up, updating firmware, or trouble is
occurring.
External Output (AW‑UE50 only)
Select the signal type output from the External Output signal lines
(Output1, Output2) of the RS‑422 connector. (→ page 17)
Output1 [Off
*
, R‑Tally, G‑Tally]
Output2 [Off
*
, R‑Tally, G‑Tally]
Off Signal is not output.
R-Tally The reception status of the red tally signal is output.
G-Tally The reception status of the green tally signal is output.
*
: Factory settings
86
Web screen configurations (continued)
To Next Page
Loading...
