36
This monitor permits remote operation via GPI/RS-232C terminal.
GPI screen items correspond to the following terminals. Use the GPI menu to assign functions to each terminal (
J
page 29).
Functions assigned to terminals are executed when GND (pin 5) is short-circuited (ON) or open (OFF).
■ Operating conditions
Level operation: Operates when GND is short-circuited.
Edge operation: Operates when GND changes from
open to short-circuited.
* When level operation is assigned to more than one
terminal, the function operates as long as one of the
terminals is short-circuited.
*1 When a 16:9 marker and a 4:3 marker are simultaneously selected and activated on a 16:9 aspect ratio display,
both markers are displayed.
*2 When a 16:9 marker and a 4:3 marker are simultaneously displayed, the background of the marker selected by
the 16:9 marker is controlled.
*3 When “R-TALLY” and “G-TALLY” simultaneously go on, the tally color changes to orange.
*4 This is only enabled when “RGB-VIDEO” is selected under “YP
BPR/RGB” in the “INPUT SELECT” menu.
GPI terminal
Pin number Signal
1GPI1
2GPI2
GPI Terminal (9P) 3 GPI3
4GPI4
5GND
6GPI5
7GPI6
8GPI7
9GPI8
Assigned item Function Operating conditions
UNDEF
Undefined (no function assigned) —
MARKER1
ON/OFF
*1
Switches marker display defined in “GPI PRESET1”
(J page 18) in the “MARKER” menu.
Level operation
(Short-circuited: ON, Open: OFF)
MARKER2
ON/OFF
*1
Switches marker display defined in “GPI PRESET2”
(J page 18) in the “MARKER” menu.
Level operation
(Short-circuited: ON, Open: OFF)
MARKER
BACK HALF
*2
Reduces the brightness of the background outside the
marker displayed in “GPI PRESET1” (
J
page 18) to 50%.
Level operation
(Short-circuited: ON, Open: OFF)
MARKER
BACK BLACK
*2
Reduces the brightness of the background outside the
marker displayed in “GPI PRESET1” (
J
page 18) to 0%.
Level operation
(Short-circuited: ON, Open: OFF)
CENTER MARKER
Turns the center marker display on and off. (When
other markers are displayed, this marker is
superimposed on other markers.)
Level operation
(Short-circuited: ON, Open: OFF)
INPUT SEL. VIDEO
Switches the input line to VIDEO. Edge/level operation
INPUT SEL. SDI1
Switches the input line to SDI1. Edge/level operation
INPUT SEL. SDI2
Switches the input line to SDI 2. Edge/level operation
INPUT SEL.
YP
BPR/RGB
Switches the input line to YPBPR/RGB. Edge/level operation
INPUT SEL. DVI-D
Switches the input line to DVI-D. Edge/level operation
SD ASPECT
Sets the aspect ratio for SD signal input. (Disabled during
HD and PC signal input)
Level operation
(Short-circuited: 16:9, open: 4:3)
SCAN
Switches the scan mode between “UNDER” and
“NORMAL”. (Disabled during PC signal input)
Level operation (Short-circuited: UNDER,
Open: NORMAL)
R-TALLY
*3
Lights the red tally. Level operation
(Short-circuited: ON, Open: OFF)
G-TALLY
*3
Lights the green tally. Level operation
(Short-circuited: ON, Open: OFF)
MONO
Switches between color and monochrome (MONO).
(Disabled during PC signal input)
Level operation (Short-circuited:
monochrome, Open: color)
GAMMA SEL. FILM
Switches the gamma curve to FILM mode. Level operation (Short-circuited: FILM
mode, Open: STANDARD mode)
GAMMA SEL. STDIO/
PST
Switches the gamma curve to STDIO/PST mode. Level operation (Short-circuited: STDIO/
PST mode, Open: STANDARD mode)
SELECT SYNC
*4
Selects the SYNC when using
YPBPR/
RGB-VIDEO input.
Level operation
(Short-circuited: EXT, Open: INT)
PIXEL TO PIXEL
Switches screen display between input size and
display size.
Level operation
(Short-circuited: ON, Open: OFF)
REMOTE Specifications
To Next Page
Loading...
