37
Main Menu (continued)
Functions displayed during FUNCTION button operation
Pressing any of the <FUNCTION1> to <FUNCTION5> buttons displays the operations assigned to each button as shown below.
Setting Display
HV DELAY [DELAY OFF] → [H DELAY] → [V DELAY] → [HV DELAY]
BLUE ONLY [BLUE ONLY OFF]→ [BLUE ONLY ON]
GAMMA SELECT [GAMMA STANDARD] → [GAMMA FILM] → [GAMMA STDIO/PST] → [GAMMA CINEMA]
SD ASPECT [4:3]→[16:9]
SCAN [NORMAL SCAN]→[UNDER SCAN]
SUB WINDOW [SINGLE]→[FULL/PART]→[STILL]
WFM/VECTOR [WFM/VECTOR OFF]→[WFM Y ON]→[WFM R ON]→[WFM G ON]→[WFM B ON]→
[VECTOR×1/×2S/×2/×4/×8]
MARKER [MARKER OFF]→
[4:3 MARKER/13:9MARKER/14:9MARKER/CNSCO2.39 MARKER/CNSCO2.35 MARKER/2:1 MARKER/
VISTA MARKER/95% MARKER/93% MARKER/90% MARKER/88% MARKER/80% MARKER/
xx% MARKER
*
10
/xx%/yy% MARKER
*
11
]
*
10
xx% indicates an 80 to 100% USER setting
*
11
xx%/yy% is the VAR set value for 80 to 100 % aspect ratio
• When the set values for both [16:9] and [4:3] are something other than [OFF] in the [MARKER] menu
settings, the [16:9] set value is displayed in the first half, and the set value of [4:3] is displayed in the
second half.
WHITE BALANCE [WHITE BALANCE VAR 1/2/3]
PIXEL TO PIXEL [PIXEL TO PIXEL OFF]→[PIXEL TO PIXEL LEFT/CENTER/RIGHT]
PIXEL POSITION [PIXEL TO PIXEL LEFT]→[PIXEL TO PIXEL CENTER]→[PIXEL TO PIXEL RIGHT]
FOCUS-IN-RED [FOCUS-IN-RED OFF]→[FOCUS-IN-RED ON]
LEVEL METER [METER OFF]→[METER 2 CH/4 CH/8 CH]
CROSS HATCH [CROSS HATCH OFF]→[CROSS HATCH LOW]→[CROSS HATCH HIGH]
MONO [MONO OFF]→[MONO ON]
BLACK MODE [BLACK MODE OFF]→[BLACK MODE ON]
TIME CODE [TC OFF]→[LTC/VITC/LUB/VUB/LTC+LUB/VITC+VUB]
CLOSED CAPTION The displayed items differ depending on the [CC TYPE] selection.
When the [CC TYPE] setting is [CEA-608 (ANC)], [CEA-608 (VBI)] or [CEA-608 (708)]:
[CC OFF]→[CC1/2/3/4]
When the [CC TYPE] setting is [CEA-708]:
[CC OFF]→[SRV1/2/3/4/5/6]
When the [CC TYPE] setting is [OP-42]:
[CC OFF]→[OP-42]
When the [CC TYPE] setting is [OP-47]:
[CC OFF]→[OP-47]
AUDIO MUTE [AUDIO MUTE OFF]→[AUDIO MUTE ON]
AUDIO OUT SEL. [SDI1]→[SDI2]
ANAMO [ANAMO OFF]→[ANAMO ON]
TWO WINDOW [SINGLE]→[TWO M/M]
Y MAP [Y MAP OFF]→[Y MAP ON]
PICTURE ASSIST [PICTURE ASSIST OFF]→[PICTURE ASSIST ON]
R COLOR [R COLOR ON]→[R COLOR OFF]
G COLOR [G COLOR ON]→[G COLOR OFF]
B COLOR [B COLOR ON]→[B COLOR OFF]
ZEBRA [ZEBRA OFF]→[ZEBRA INT.]→[ZEBRA EXT.]→[ZEBRA INT.+EXT.]
ZEBRA LEVEL [SETTING]
2D/3D ASSIST [2D]→[3D ASSIST]
<Note>
• [WHITE BALANCE] and [ZEBRA LEVEL] is switched to adjustment mode with a <FUNCTION> button, and operating status is not
displayed.
• SUB WINDOW, TWO WINDOW, PICTURE ASSIST of the 2-screen display function are mutually exclusive functions - when one is
on, the other two are off. For this reason, when one of the 2-screen display functions is on, the operating status of the function that is
on is displayed when a screen is opened using the <FUNCTION> button.
• [CC1/2/3/4] and other [
***
/
***
] indications denote set values in relevant menus.
To Next Page
Loading...
