67
REMOTE Specifications (continued)
Query commands
No
Command parameter
Description Response data
1 QIS INPUT SELECT 00:SDI1 01:SDI2 02:DVI-ANALOG-VIDEO 04:VIDEO
06:DVI-ANALOG-COMP. 09:DVI-DIGITAL-VIDEO
10:DVI-DIGITAL-COMP. 11:HDMI 12:INT-SG
2 QPC:CON CONTRAST 00 to 60
3 QPC:BRI BRIGHT 00 to 60
4 QPC:CRO CHROMA 00 to 60
5 QPC:PHA PHASE 00 to 60
6 QPC:VOL VOLUME 00 to 60
7 QBL BACKLIGHT 000 to 100
8 QMK:MAK
MARKER
*
3
00:OFF
01:80 %
02:88 %
03:93 %
04:95 %
05:14:9
06:13:9
07:4:3
08:90 %
09:CNSCO2.35
10:VISTA
11:2:1
12:CNSCO2.39
080 to 100:USER 80 % to 100 %
xxxyyy:VAR.H.80 % to 100 %
V.80 % to 100 %
(xxx:080 to 100
yyy:080 to 100)
9 QMK:BAK MARKER BACK 0:NORMAL 1:HALF 2:BLACK
10 QMK:CMK CENTER MARKER 0:OFF 1:ON
11 QCH CROSS HATCH 0:OFF 1:LOW 2:HIGH
12 QCW CROSS HATCH WIDTH 0:SMALL 1:LARGE
13 QMK:COL MARKER COLOR 0:WHITE 1:BLACK 2:RED 3:GREEN 4:BLUE
14 QMK:VMK CROSS MARKER xxxxyyyy: Position range 00000000(off)
(xxxx:0020 to 1899 yyyy:0020 to 1059)
15 QGM GAMMA SELECT 1:STANDARD 2:FILM 3:STDIO/PST 4:CINEMA
16 QCT COLOR TEMP 00:D56 01:D65 02:D93 03:VAR1 04:VAR2
05:VAR3 10 to 73:USER0 to 63
17 QPC:SHP SHARPNESS MODE 0:LOW 1:HIGH
18 QPC:SHH SHARPNESS H 00 to 30: Horizontal sharpness set value
19 QPC:SHV SHARPNESS V 00 to 30: Vertical sharpness set value
20 QIP IP MODE 0:MODE1 1:MODE2
21 QMO MONO 1:OFF 2:ON
22 QAS SD ASPECT 0:16:9 1:4:3
23 QSC SCAN 0:NORMAL 1:UNDER
24 QZB ZEBRA 0:OFF 1:INT. 2:EXT. 3:INT.+EXT.
25 QZI ZEBRA LEVEL INT. xxxyyy: INT. range (-07 to 000 to 109)
(xxx:MIN value yyy:MAX value)
26 QZE ZEBRA LEVEL EXT. xxxyyy: EXT. range (-07 to 000 to 109)
(xxx: MIN value yyy: MAX value)
27 QCS COLOR SPACE 0:SMPTE-C 1:EBU 2:ITU709
28 QNS NTSC SETUP 0:OFF 1:7.5 %
29 QDT DVI TYPE 0:DIGITAL 1:ANALOG
30 QDD DVI DIGITAL MODE 0:AUTO 1:VIDEO 2:COMP.
31 QDA DVI ANALOG MODE 0:YP
B
P
R
1:RGB-COMP.
*
3
When both 16:9 and 4:3 markers are displayed, the 16:9 marker state is returned.
(Continued on next page)
To Next Page
Loading...
