FUNCTIONS
FUNCTIONS
65
SETUP
Setup
Setup
TV Aspect
Progressive
TV System
16:9
Off
PAL
AV1 Output ( Scart )
Video
AV2 Settings
Setup
AV2 Input
RGB / Video
AV2 Settings
Ext Link
Ext Link 2
RGB / Video
AV2 Input
RGB
Video
S Video
HDMI Settings
TAB
SELECT
RETURN
ENTER
Connection
Setting
ENTER
ENTER
Option
TV Aspect
[16:9] [4:3] [Letterbox]
Progressive
[On] [Off]
On: The signal is displayed in full-picture quality using COMPONENT VIDEO OUT.
Cannot be changed over when HDMI [Digital Audio Output] is set to [Automatic] and
the HDMI terminal is being used.
TV System
AV1 Output ( Scart )
AV2 Settings
AV2 Input
[PAL] [NTSC]
[RGB / Video] [RGB] [Video] [S Video]
AV2 Input
Ext Link
Ext Link
[Ext Link1] [Ext Link 2]
HDMI Settings
Video ( with Component ): Factory-default settings.
S Video ( with Component ): Select when a TV is connected that can receive an
S Video signal.
RGB 1 ( without Component ): Select this setting when a TV set is connected up
which can receive an RGB signal. Select this mode if you always want to see the
picture in RGB signals.
RGB 2 ( without Component ): Select this setting when a TV set is connected up
which can receive an RGB signal. Select this mode if you always want to see menus
in RGB signals.
[Video ( with Component )]
[S Video ( with Component )]
[RGB Component )]
[RGB 2 ( without Component )]
1 ( without
9966
ENTER
RETURN
SELECT
99
19
To Others
Tuning
Disc
Picture
Sound
Display
Connection
Others
Tuning
Disc
Picture
Sound
Display
Connection
Others
Select the TV screen format of your television. Programmes in 16:9 format are recorded
in 4:3 format. 16:9 format is used to record to HDD/RAM.
Letterbox: Black bars appear on the upper and lower edges of the screen (16:9).
PAL: You connect the unit to a PAL or multi-system television. Programmes that were
recorded with NTSC are played as PAL60.
NTSC: You connect the unit to an NTSC television. Programmes that were recorded
with NTSC are played as NTSC.
HDMI (High Definition Multimedia Interface) is a digital interface for Audio and Video.
One single cable transfers both digital video data (picture data) and also digital audio
data. There is no longer any need to convert analogue-digital or digital-analogue.
HDMI works without data compression so that there is therefore no quality loss from
the system.
Perform the settings in the
following submenus for the
connected unit.
RGB / Video: When receiving or recording RGB output from external equipment.
RGB, Video, S Video: The input is switched to the selected signal.
Ext Link 1: For digital receivers that send a special recording control signal,
for example, the F.U.N. receiver (TU-DSF41).
Ext Link 2: External recording control for satellite or digital receivers (video signal).
AV-Link function
Switching between television reception and
the signal from the DVD Recorder. This
function is only possible if the AV1 Output
is set to [Video ( with component )] or
[RGB 2 ( without component )].
DVD recorder signal: Press ENTER + 0.
DVD appears on the display.
Television reception: Press the buttons again.
TV appears on the display.
Active Antenna
Off
Active Antenna
On: When you connect an aerial which shares the power circuit of the DVD Recorder.
Start the Auto-Setup again after making the adjustment and check the
signal properties.
[On] [Off]
9960
Not NTSC:
RGB / Video, S VIDEO, Ext Link 1, Ext Link 2.
To Next Page
Loading...
