Panasonic DP-C305 - Page 451

451
DP-C405/C305/C265
FEB 2008Ver. 1.1
J08 1. The Option Intermediate Roller Jam Sensor (1819-03) does not detect paper within
a predetermined time after the Paper Feed Roller starts rotating.
(Paper Tray 3)
2. The Intermediate Roller Jam Sensor (1819-01) does not detect paper within a
predetermined time after Feed clutch is on as double feed timing.
(Paper Tray 3) (DP-C405 Series)
3. The Option Intermediate Roller Sensor (1819-03) does not detect paper within a
predetermined time after the Paper Feed Roller starts rotating. (Paper Tray 4)
(DP-C405 Series)
4. The Intermediate Roller Jam Sensor (1819-01) does not detect paper within a
predetermined time after Feed clutch is on as double feed timing.
(Paper Tray 4) (DP-C405 Series)
Paper
Feed
J09 The Option Intermediate Roller Jam Sensor (1819-03) does not detect paper within a
predetermined time after the Paper Feed Roller starts rotating. (Paper Tray 4)
J16 The Registration Sensor 2 (1918-01) does not detect paper within a predetermined
time. (Paper Tray 1-4) (DP-C405/C305)
J18 The Registration Sensor 1 (2110 : ROHP PCB) does not detect paper within a
predetermined time. (Paper Tray 1-4)
J19 The Registration Sensor 1 (2110 : ROHP PCB) does not detect paper within a
predetermined time. (ADU)
J26 1. The Intermediate Roller Jam Sensor (1819-01) detects paper before the start of
initialization. (DP-C405/C305, DP-C354/C322 Series)
2. The Intermediate Roller Jam Sensor (1819-01) detects paper before the Feed
Roller starts rotating. (Paper Tray 1-2) (DP-C405/C305)
J27 1. The Intermediate Roller Jam Sensor (1819-01) detects paper before the start of
initialization. (DP-C405 Series)
2. The Intermediate Roller Jam Sensor (1819-01) detects paper before the Feed
Roller starts rotating. (Paper Tray 3-4)
J28 The Option Intermediate Roller Jam Sensor (1819-03) detects paper before the start
of initialization.
J30 1. The Registration Sensor 1 (2110 : ROHP PCB) goes Off within a predetermined
time. (Abnormal Paper Length)
2. The Registration Sensor 2 (1918-01) goes Off within a predetermined time.
(Abnormal Paper Length) (DP-C405/C305)
Fuser
3. Printing does not go Off after the Fuser Exit Sensor (1819-32) goes Off. (Abnormal
Paper Length)
Paper Exit
J31 The Registration Sensor 1 (2110 : ROHP PCB) does not go Off within a predetermined
time.
Paper
Feed
J32
The Registration Sensor 2 (1918-01) does not go Off within a predetermined time.
(DP-C405/C305)
J33 1. The Registration Sensor 1 (2110 : ROHP PCB) detects paper before the start of
initialization.
2. The Registration Sensor 1 (2110 : ROHP PCB) detects paper before the Feed
Roller starts rotating. (Paper Tray 2-4)
3. The Registration Sensor 1 (2110 : ROHP PCB) detects paper before the Feed
Roller starts rotating. (Sheet Bypass)
J34 1. The Registration Sensor 2 (1918-01) detects paper before the start of initialization.
(DP-C405/C305)
2. The Registration Sensor 2 (1918-01) detects paper before the Feed Roller starts
rotating. (Paper Tray 2-4) (DP-C405/C305)
J35 The Media type (Transparency) is mis-matched.
Jam Error Codes (J Code) Table
Code Contents Section