z Preset Setting
Preset Speed Unit [Speed Table, Time]
When reproducing the information such as camera direction
registered in the preset memory, you can select whether to specify
the playback time by speed or by time.
Speed Table Specify the speed when playing during preset playback.
Time Specify the time when playing during preset playback.
Factory settings: Speed Table
Preset Speed Table [Slow, Fast]
Set the preset speed table (Slow, Fast). During preset playback,
presets are performed at [Preset Speed] (1 to 30) values that are
based on the table set here.
This is only enabled when [Preset Speed Unit] is set to [Speed Table].
Factory settings: Fast
Preset Speed [1 to 30/1s to 99s]
When [Preset Speed Unit] is [Speed Table]: [1 to 30]
Set the pan/tilt operation speed in 30 steps when playing back the
preset memory.
Factory settings: 20
<NOTE>
• When you set large [Preset Speed] values, the image may sway
when the movement stops.
When [Preset Speed Unit] is [Time]: [1s to 99s]
Set the pan/tilt operation time between 1 and 99 seconds when
playing back the preset memory.
Factory settings: 20s
<NOTE>
• Depending on the movement distance of pan/tilt, there may be a
difference compared to the specified time.
Preset Acceleration [Manual, Auto]
Sets whether to perform advance setting for acceleration and
deceleration speed etc. during start/stop of preset playback.
Manual Makes the advance settings for acceleration speed etc.
when starting/stopping preset playback.
Auto Automatically operates acceleration speed etc. when
starting/stopping preset playback.
Factory settings: Auto
Rise S-Curve [0 to 30]
Sets the S-curve for pan/tilt acceleration operation in 31 steps. (The
greater the number, the steeper the S-curve)
During the acceleration operation for operating at the specified speed
or time during pan/tilt operations by preset playback, the acceleration
process is performed using the S-curve specified in this setting.
This is enabled only when [Preset Acceleration] is [Manual].
Factory settings: 15
<NOTE>
• In order to limit the acceleration response, in the S-curve step, as
the acceleration speed rises, the limit is automatically applied.
Fall S-Curve [0 to 30]
Sets the S-curve for pan/tilt deceleration operation in 31 steps. (The
greater the number, the steeper the S-curve)
During the fall acceleration operation for operating at the specified
speed or time during pan/tilt operations by preset playback, the
deceleration process is performed using the S-curve specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual].
Factory settings: 15
<NOTE>
• In order to limit the deceleration response, in the S-curve step, as
the deceleration speed rises, the limit is automatically applied.
Rise Acceleration [1 to 255]
Sets the acceleration speed for pan/tilt acceleration operation in 255
steps. (The acceleration speed increases as the number increases.)
During the acceleration operation for operating at the specified speed
or time during pan/tilt operations by preset playback, the acceleration
process is performed using the acceleration speed specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Speed Table].
Factory settings: 128
<NOTE>
• As the speed specified for [Preset Speed] is given priority as the
maximum speed attained in preset playback, if the acceleration
speed specified here is small, this functionality may not operate as
specified.
Fall Acceleration [1 to 255]
Sets the deceleration speed for pan/tilt deceleration operation in 255
steps. (The deceleration speed increases as the number increases.)
During the deceleration operation for operating at the specified speed
or time during pan/tilt operations by preset playback, the deceleration
process is performed using the deceleration speed specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Speed Table].
Factory settings: 128
<NOTE>
• As the speed specified for [Preset Speed] is given priority as the
maximum speed attained in preset playback, if the deceleration
speed specified here is small, this functionality may not operate as
specified.
Rise Ramp Time [0.1s to 10.0s]
Sets the acceleration time for the time specific operation during preset
playback. (Sets between 0.1s to 10.0s in 0.1s increments)
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Time].
Factory settings: 0.1s
<NOTE>
• As the time specified in [Preset Speed] takes precedence as the
total time for preset playback, if the time specified here is more than
half of the time specified in [Preset Speed], this functionality will not
operate as specified.
• When the acceleration operation cannot be performed within the
specified time even at maximum acceleration speed of the device,
the operation will not be performed by the specified time.
Fall Ramp Time [0.1s to 10.0s]
Sets the deceleration time for time specified operations during preset
playback. (Sets between 0.1s to 10.0s in 0.1s increments)
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Time].
Factory settings: 0.1s
<NOTE>
• As the time specified in [Preset Speed] takes precedence as the
total time for preset playback, if the time specified here is more than
half of the time specified in [Preset Speed], this functionality will not
operate as specified.
• When the deceleration operation cannot be performed within the
specified time even at maximum fall deceleration of the device, the
operation will not be performed by the specified time.
162
Web screen configurations (continued)
To Next Page
Loading...
