Panasonic KX-NS0154 - Page 41

41
KX-NS0154
L4 MEMXD2_LCDD4 Not used O
L5 VDDIO_RGMII RGMII I/O PI
L6 VDDIO General I/O PI
L7 GND GND Connection P
L8 GND GND Connection P
L9 GND GND Connection P
L10 GND GND Connection P
L11 GND GND Connection P
L12 GND GND Connection P
L13 PLL3_AVDD PLL3 Analog PI
L14 IF_EN_AD TDM-DTX for IC503 O
L15 IF_DATA_AD TDM-SCLK for IC503 I
L16 IF_CLK_IF RFAPU/APU Interface Clock out (Not used) O
L17 AMPOUT2 Output of Out Amplifier 2 (Not used) O
L18 AMPOUT3 Output of Out Amplifier 3 (Not used) O
L19 DIFFIN1P Positive Input In Amplifier 0 (Not used) I
M1 MEMXD1_LCDD3 Not used O
M2 MEMXD4_LCDD6 Not used O
M3 MEMXD15_LCDD21 not used O
M4 MEMXD0_LCDD2 Reset SW detect I
M5 VCC_USB2 USB2 I/O power supply PI
M6 VDDL_USB1 USB1 1.2 V PI
M7 OSC12M_VSS Oscillator 12 MHz GND P
M8 VDD 1.2 V Core PI
M9 GND GND Connection P
M10 VDD 1.2 V Core PI
M11 GND GND Connection P
M12 GND GND Connection P
M13 VDDIO_APU DAIF I/O Voltage 1.8 V PO
M14 VDDIO_RFAPU RFAPU I/O PI
M15 VCC_AMP_OUT VCC for AFE Out Amplifiers PI
M16 GND_AMP_OUT GND for AFE Out Amplifiers P
M17 DIFFIN0N Negative Input In Amplifier 0 (Not used) I
M18 DIFFIN0P sitive Input In Amplifier 0 (Not used) I
M19 DIFFIN1N Negative Input In Amplifier 1 (Not used) I
N1 MEMXD12_LCDD18 PHY link signal detect I
N2 MIIRXER_EXTINT12 MII Rx Error I
N3 MII_TXER_SPI1CS1 MII TX Error O
N4 MDC Management Data Clock O
N5 VDDRA_USB1 USB1 3.3 V PI
N6 USB1VRES USB1 Reference Circuit Input I
N7 OSC12M_VDD12 Oscillator 12 MHz 1.2 V PI
N8 VDDIO_NFLQSPI QSPI I/O PI
N9 VDDIOC Keyboard I/O PI
N10 VDDIO General I/O PI
N11 DGPIO30 GPIO (Not used) O
N12 VDD 1.2 V Core PI
N13 VDD_ANA 1.8 V Core Analog Output Voltage PO
N14 MICPWR1 Microphone Power 1 Output (Not used) PO
N15 SINGIN0 Input of Single-ended In Amplifier 0 (Not used) I
N16 VCCA Analog VCC PI
N17 GNDA Analog GND P
N18 XI13M 13.824 MHz XTAL Input I
N19 BCLK BCLK output (Not used) O
P1 MIIRXD1_RGMIIRD1 MII RX Data I
P2 MIIRXD3_RGMIIRD3 MII RX Data I
P3 MIIRXD2_RGMIIRD2 MII RX Data I
P4 MIIRXCRS_U2TX MII_RXCRS I
P5 USB1ID USB1 ID I
P6 USB1VBUS USB1 Vbus PI
P7 KEY_COL6 Trace (Not used) O
P8 KEY_ROW9 Trace (Not used) O
P9 KEY_ROW8 Trace (Not used) O
P10 KEY_ROW7_IIC2SDA Trace (Not used) O
P11 U1CTS_DIGMIC_DATA UART1 Clear To Send (Not used) I
P12 DGPIO31 GPIO (Not used) O
P13 TPX2 Not used I/O
Pin No. Terminal Name Contents of Control I/O setting Remark