26
System Programming
Other Programs
• Call Blocking Mode Setting
Assigns whether or not to prevent the DTMF
signal from being sent to a CO line. This feature
is useful when a Central Office in your country
accepts both tone and pulse signals or when you
have access to your host PBX with a pulse dial.
Input Format: #20 [A]
• [A]=0:DISABILITATO(default)/ 1: ABILITATO
• Host PBX Access Code Assignment
Assigns a Host PBX access code to make an
outside call, if the system is installed behind the
host PBX. A pause is automatically inserted after
the access code and the toll restriction feature
applies to the number after the code.
Input Format: #21 [A] [code] #
• [A]=1: LU1/ 2: LU2
• [code] = 2 digits max. (Default : NO
REGISTRAZ)
• Hookswitch Flash Time Assignment
Sets the time to send the flash signal to each CO
line.
Input Format: #22 [A] [B]
• [A]=1: LU1/ 2: LU2
• [B]=0: 80 MS/ 1: 100 MS (default)/ 2: 160 MS/
3: 300 MS/ 4: 600 MS / 5: 900 MS/
6: 1200 MS
• CO Pulse Selection
Assigns to send the pulse to CO line during a
conversation with an outside party when the “#01
Dial Type Selection” program is assigned as
“Pulse”.
Input Format: #23 [A]
• [A]=0:DISABILITATO/ 1: ABILITATO
(default)
• Call Incoming Mode Selection (Day/Night)
Assigns whether to use the DISA feature or not.
This program is available when the DISA/FAX
Detect card is installed.
Input Format: #24 (for day)/#78 (for night)
[A] [B]
• [A]=1: CO1/ 2: CO2
• [B]=0: NORMAL/ 1: DISA (default)
• Bell Off Detection
Sets the time between one bell signal detection
and the next signal from a Central Office.
Input Format: #25 [A]
• [A]=1: 6 SEC (default)/ 2: 12 SEC
• Intercom Alerting Assignment
Assigns the intercom alerting mode to each
extension when an intercom call reaches.
Input Format: #30 [A] [B]
• [A]=1 through 6 (corresponding to extension no.
21 through 26)
• [B]=0: TONO CHIAMATA(default)/
1: CHIAMATA VOCE
• Paralleled Telephone Connection
Assigns whether each extension will be connected
in parallel with a single line telephone or not.
Input Format: #31 [A] [B]
• [A]=1 through 6 (corresponding to extension
no. 21 through 26)
• [B]=0:DISABILITATO (default)/
1:ABILITATO
• Tone Waiting Time After OGM
Sets the time between sending an outgoing mes-
sage and sending the ringback tone.
Input Format: #40 [A]
• [A]=0: 0 SEC/ 1: 5 SEC (default)/
2: 10 SEC/ 3: 15 SEC
• Hold Recall Time
Assigns the length of the hold recall timer. The
hold recall timer is used to alert an extension that
a call has been held for an extended period of
time.
Input Format: #50 [A]
• [A]=0: 0 SEC (default)/ 1: 1 MIN / 2: 2 MIN/
3: 3 MIN/ 4: 4 MIN/ 5: DISABILITATO
• Hold Mode Selection for SLT
Assigns the method to put a call on hold with
SLTs.
Input Format: #51 [A]
• [A]=1: MODO 1 (hooking) (default)
2: MODO 2 (hooking and dial 6)
• CO Line Access Number Selection
Selects the automatic line access number.
Input Format: #52 [A]
• [A]=1: 9/ 2: 0 (default)
• Transfer Recall Time
The transfer recall timer is used to alert an exten-
sion that a transferred call has not been answered
for an extended period of time.
Input Format: #54 [A]
• [A]=1: 30 SEC (default)/ 2: 2 MIN
• Music on Hold Use
Selects whether or not to use internal music as the
music on hold.
Input Format: #55 [A]
• [A]=1: MODE 1 (NO MUSIC) /
2: MODE 2 (MUSIC)(default)
To Next Page
Loading...
