Panasonic KX-TCD300FXS - Page 87

28.3.3. Flash Time Setting
Address Initial
Type
Name Description Default value Country
Setting
0x034D 1 EEP_FlashTime1 Calibrated loop-break time for “80 ms”
Unit: 10 ms, defaults to 80 ms
0x08 x
0x034E 1 EEP_FlashTime2 Calibrated loop-break time for “90 ms”
Unit: 10 ms, defaults to 90 ms
0x09 x
0x034F 1 EEP_FlashTime3 Calibrated loop-break time for “100 ms”
Unit: 10 ms, defaults to 100 ms
0x0A x
28.3.4. Clip (Caller ID) configuration
Address Initial
Type
Name Description Default value Country
Setting
0x01F9 1 EEP_ClipDetectConfig CLIP detect configuration
Bit0-2:Mode...1:DTMF only, 2:FSK only, 3:FSK/DTMF
both, 4:Russian CLIP
Bit3:Onhook...1=enable, 0=disable
Bit4:Offhook...1=enable, 0=disable
Bit5:MsgWaiting...1=enable, 0=disable
Bit6:KpnVmwi...1=enable, 0=disable
Bit7:Unused
0x3B x
0x01FA 1 EEP_FskInterdigitTimeout FSK Interdigit timeout
Unit: 10ms, Defalut: 80ms
0x08 x
0x01FB 1 EEP_RuClipReqLev RCID REQ signal Level
Default: -4.3dBm
0x00, 0x19 x
0x03AE 1 EEP_ClipRingConfig Ring configuration
Bit0:Rpas...1=enable, 0=disable
Bit1:RpasAlert...1=enable, 0=disable
Bit2:Rpas2LongAlert...1=enable, 0=disable
Bit3:Suppress1stRing...1=enable, 0=disable
Bit4:Check1stRing...1=enable, 0=disable
Bit5-7:Unused
0x00 x
0x03AF 1 EEP_ImpSetConfig Impedance Set configuration
Bit0:Polarity...1=enable, 0=disable
Bit1:Dtas...1=enable, 0=disable
Bit2:Rpas...1=enable, 0=disable
Bit3:PowerRing...1=enable, 0=disable
Bit4:LearnImpPattern...1=enable, 0=disable
Bit5:CheckPolStatus...1=enable, 0=disable
Bit6-7: Unused
0x15 x
0x03B0 1 EEP_ImpRemConfig Impedance Remove configuration
Bit0:Polarity...1=enable, 0=disable
Bit1:Ringing...1=enable, 0=disable
Bit2:ClipReceived...1=enable, 0=disable
Bit3:Offhook...1=enable, 0=disable
Bit4:ChszDet...1=enable, 0=disable
Bit5-7:Unused
0x0F x
0x03B1 1 EEP_CasAckDtmf CAS Acknowledge DTMF tone
00:DTMF 0 - 09:DTMF 9
0A:DTMF A
0B:DTMF B
0C:DTMF C
0D:DTMF D
0E:DTMF *
0F:DTMF #
0x0D x
0x03B2 1 EEP_DtmfReceiveDataCoun
t
Valid Receive data Count (for INDIA) 0x04 x
0x03B3 1 EEP_ClipPhaseConfig CLIP phase set configuration
Bit0:ForwardNumber...1=enable, 0=disable
Bit1:CallingNumber...1=enable, 0=disable
Bit2:Dutch...1=enable, 0=disable
Bit3:Chinese...1=enable, 0=disable
Bit4:PriorityCheck...1=enable, 0=disable (for France)
Bit5-6:AddZero...0:no add zero, 1:add zero absolutely
2:Check Number’s top is zero. If it is zero, add zero.
Bit7:Unused
0x04 x
0x03B4 1 EEP_ClipPhaseConfig2 CLIP phase set configuration
Bit0:FskRemoveParity...1=enable, 0=disable
Bit1:AutoRappel...1=enable, 0=disable
Bit2:KpnStartEndNg
Bit3:CheckCidSendFlg
Bit4-7:Unused
0x01 x
0x03B5 1 EEP_AddZeroDataCount Valid data for Add Zero (for NewZealand) 0x05 x
87
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT