Load ihe
batteries
as follows:
O
Remove
the battery
compartment
lid.
@
etace
the batteries
in the battery
compartment as
indicated
inside the battery compartment.
€)
Replace
the lid.
Note:
.The
infra-red beam should
be
tansmitted directly
at the
lnfra-red Remote Control
Receiver
on the front of
the
VTR.
.Direct
sunlight
may interfere
with the beam.
.The
lightsensing
angle of
the Infra-red
Remote Conirol
Receiver in the
VTR is about
30" tor each side
from the
centre.
.The
unit should be
used within a
ranqe of about
7 meters
from the front of the
VTR.
How
to
Operate
the
Digital Scanner
Set
the Digital Scanner
On/Off Switch to "ON".
.lf
no operation
is
performed
for more than
25
seconds
(4
minutes
during setting
of the clock
time), the scanner
will
automatically
switch over
to the
power-saving
standby
condition
and
the lamp
will
go
off.
(ln
this case,
if bar
codes
have already
been read but
not
yet
transmitted to
the VTR, the data
will be cancelled.)
.When
the Digital
Scanner On/Otf Switch
is set to
"ON"
but
the
lamp is
not lit, set the switch
to
"OFF"
and then
to
"ON"
again.
Note:
The bar codes
"VTR
1" and "VTR
2" in the column
"REMOTE
MODE" on the
Programming Sheet cannot be
used with this unit.
.lf
the bar
code
"VTR
2" is traced by mistake, transmission
to the
VTR becomes impossible.
To remedy this condi-
tion. trace the
"VTR
1" bar code.
(The
indication
"VTR
2"
in the
Bar
Code
Reader
Display will disappear.)
Place the Digital Scanner
vertically on the Small
Box.
Trace
the bar code
quickly
in the direction
of the arrow.
.Treat
the Programming
Sheet
with care. lf the sheet
geis
dirly or scratched,
the bar code
reading
may
become
impossible.
.Protect
the Digital Scanner
lrom strong
shocks and
vibration. Keep it away
from water and
places
with
high temperature
and humidity.
.lf
the bar
code is traced slowly,
it cannot
be read
correctly.
.When
there is no
"Beep"
sound,
the reading
of the
bar code
is incomplete. Trace
the bar code agatn.
.When
using the
Programming sheet,
put
it on
tlat
sudace:
Reading the bar codes
while
holding it
in
your
hand or bending
it, may
result in incorrect
operation.
.Do
not
deviate
from the bar code,
nor stop
tractng
haltway.
.Do
not stant
the
scanner
to trace
the bar code.
Recommendalion
To
save battery
power,
make sure
to
set
the Digital Scanner
On/Otf Switch
to
"OFF"
after using the Digital Scanner.
When the batteries are
exhausted, the bar code
reading
can
no longer be
performed.
Although the
lamp in ihe tip of the Bar Code
Reading
Section
lights
up:
.No
figures appear in the Bar Code
Reader Display
.No
beep sounds
is heard;
The tip of the Bar Code
Reading Section is
probably
clogged
with
dirt.
Cleaning
O
Turn the Cap of Bar Code
Reading Section
45"
coun-
terclockwise, as shown below.
.Remove
dirt and
dust from the
hole
ol the Cap.
(A)
(B)
n"j"/v"*
H
@
Gently wipe the tip ol the lamp with a soft
cloth.
ns-
LamP
A9
(ffi)
.Reattach
the
Cap
and
loct< it
by
Ff-l
turning il clockwise.
Trace the bar
code
Bar Code/
completely
past
the
lasl bar.
sound
indicates
that the bar code
was read
completely.
(8)
To Next Page
Loading...
