Panasonic PT-FRQ50 - Page 126

Chapter 4 Settings — [PROJECTOR SETUP] menu
126 - ENGLISH
[USER SETTINGS]
The user data to return to factory default settings can be selected arbitrarily.
The projector goes into the standby status after executing [INITIALIZE].
For details of operation, refer to “Initializing the settings by selecting the items” (
x
page 126).
[REGISTERED SIGNAL ONLY]
Deletes all the signals registered in [SIGNAL LIST]. All the setting values saved for each registered
signal are also deleted.
[NETWORK/E-MAIL ONLY]
Returns all the setting items under the [NETWORK] menu and all the setting items under the
operation page in the [Detailed set up] page and the Crestron Connected of the web control screen to
the factory default settings.
f
The items of [Time Zone], [Date], and [Time] in the [Adjust clock] page of the web control screen do
not return to the factory default settings.
f
The information such as the self-signed certicate already created in the [Certicate] page of the
web control screen or the server certicate already installed is not deleted.
[LOGO IMAGE ONLY]
Deletes the image registered in [USER LOGO].
[FACTORY RESET]
Returns all the user data settings to the factory default settings. The projector goes into the standby
status after executing [FACTORY RESET].
f
Proceed to Step
5)
when anything other than [USER SETTINGS] is selected.
5) Press the <ENTER> button.
f
The conrmation screen is displayed.
6) Press
qw
to select [OK], and press the <ENTER> button.
Note
f
The security password is the password set in the [SECURITY] menu → [SECURITY PASSWORD CHANGE]. Initial password as the factory
default:
awsqawsq
f
To delete only a part of a registered signal, delete it following “Deleting the registered signal” (
x
page 129).
f
To return the setting of [Time Zone] in the [Adjust clock] page of the web control screen and the setting of the [PROJECTOR SETUP] menu
→ [DATE AND TIME] → [TIME ZONE] to the factory default settings, initialize them by one of the following methods.
g
Initializing by selecting the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET]
g
Initializing by setting the [PROJECTOR SETUP] menu → [INITIALIZE] → [USER SETTINGS] → [OTHER USER SETTING] to [INITIALIZE]
f
The self-signed certicate already created in the [Certicate] page of the web control screen or the information of the server certicate
already installed can be deleted in the web control screen.
f
If initialized by selecting [FACTORY RESET], the
[INITIAL SETTING]
screen is displayed when the projection is started the next time.
Initializing the settings by selecting the items
1) Press
as
to select [INITIALIZE].
2) Press the <ENTER> button.
f
The
[SECURITY PASSWORD
] screen is displayed.
3) Enter a security password and press the <ENTER> button.
f
The
[INITIALIZE]
screen is displayed.
4) Press
as
to select [USER SETTINGS].
5) Press the <ENTER> button.
f
The
[USER SETTINGS]
screen is displayed.
6) Press
as
to select an item.
[OPERATING MODE]
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [OPERATING MODE] is initialized.
[STANDBY MODE]
The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is initialized.
[REGISTERED SIGNAL]
All the signals registered in [SIGNAL LIST] are initialized.
[NETWORK/E-MAIL]
All the setting items under the [NETWORK] menu and all the setting items under the operation page
in the [Detailed set up] page and the Crestron Connected of the web control screen are initialized.
f
The items of [Time Zone], [Date], and [Time] in the web control screen are not initialized.
f
The information such as the self-signed certicate already created in the [Certicate] page of the
web control screen or the server certicate already installed is not initialized.
[LOGO IMAGE]
Image registered in [USER LOGO] is initialized.
[OTHER USER SETTING]
The user data other than mentioned above are initialized.