ENGLISH - 109
Noise level *
1
When set to [ (Normal)] in [Lamp control] : 39 dB
When set to [ (Eco)] in [Lamp control] : 35 dB
When set to [ (Quiet)] in [Lamp control] : 30 dB
Operating
environ-
ment
Operating
environment
temperature *
3
5 °C (41 °F) to 40 °C (104 °F) (Elevation: below 1 400 m (4 593'))
5 °C (41 °F) to 35 °C (95 °F) (Elevation: 1 400 m (4 593') ~ 2 700 m (8 858'))
Operating
environment
humidity
20 % to 80 % (no condensation)
Remote
control
Power supply
DC 3 V (AAA/R03/LR03 battery x 2)
Operating
range
Approx. 5 m (16'4-13/16") (when operated directly in front of receptor)
Weight
63 g (2.22 ozs.) (including batteries)
Dimensions
Width : 44 mm (1-23/32"), Length : 105 mm (4-1/8"), Height : 20.5 mm (13/16")
*1 Measurement, measuring conditions and method of notation all comply with ISO/IEC 21118:2012 international standards.
*2 This is an average value. It may differ depending on individual product.
*3 When the projector is operated at an elevation of 1 400 m (4 593') or less, if the ambient temperature exceeds 35 °C, [Lamp
control] will be switched to [ (Eco)] automatically to protect the projector; When the projector is operated at an elevation
between 1 400 m (4 593') and 2 700 m (8 858'), if the ambient temperature exceeds 30 °C, [Lamp control] will be switched to
[ (Eco)] automatically to protect the projector.
Note
f The part numbers of accessories and separately sold components are subject to change without notice.
r Connecting terminal
<COMPUTER 1 IN> terminal
1 (High-density D-sub 15 pin female)
RGB signal 0.7 V [p-p] 75 Ω
HD/SYNC TTL high impedance, automatic positive/negative polarity compatible
VD TTL high impedance, automatic positive/negative polarity compatible
(HD/SYNC and VD do not support 3 value SYNC.)
YP
B
P
R
signal Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
Y/C signal Y: 1.0 V [p-p] C: 0.286 V [p-p] 75 Ω S1 signal compatible
<COMPUTER 2 IN>
*1
terminal
1 (High-density D-sub 15 pin female)
RGB signal 0.7 V [p-p] 75 Ω
HD/SYNC TTL high impedance, automatic positive/negative polarity compatible
VD TTL high impedance, automatic positive/negative polarity compatible
(HD/SYNC and VD do not support 3 value SYNC.)
<MONITOR OUT> terminal
1 (High-density D-sub 15 pin female)
RGB signal 0.7 V [p-p] 75 Ω
HD/SYNC TTL high impedance,
positive/negative polarity compatible
VD TTL high impedance, positive/negative polarity compatible
<VIDEO IN> terminal
1 (Pin jack 1.0 V [p-p] 75 Ω)
<HDMI IN> terminal
1 (HDMI 19 pin, HDCP and Deep color compatible)
Audio signals: Linear PCM (Sampling frequency: 48 kHz/44.1 kHz/32 kHz)
<AUDIO IN> terminal
1 (M3 stereo mini jack, 0.5 V [rms], input impedance 22 kΩ and more)
1 (Pin jack x 2 (L-R), 0.5 V [rms], input impedance 22 kΩ and more)
<VARIABLE AUDIO OUT>
terminal
1 (M3 stereo mini jack, stereo monitor output compatible,
0 V [rms] to 2.0 V [rms] variable, output impedance 2.2 kΩ and less)
<USB A (VIEWER/WIRE-
LESS)>
*1*2
terminal
USB connector (type A x 1, output DC 5 V, 500 mA maximum)
Memory Viewer / Wireless module (Model No.: ET-WML100) compatible
<USB B (DISPLAY)> terminal
PT-LW375D, PT-LW335D, PT-LB425D,
PT-LB425T, PT-LB385D, PT-LB385T,
PT-LB355D, PT-LB355T
USB connector (type B x 1), only for USB Display
<USB B > terminal
PT-LB305D
USB connector (type B x 1)
<SERIAL IN> terminal
1 (D-sub 9 pin, RS-232C compliant, for computer control use)
<LAN>
*1
terminal
1 (for RJ-45 network connection, PJLink compatible, 10Base-T/100Base-TX)
*1 Only for PT-LW375D, PT-LW335D, PT-LB425D, PT-LB425T, PT-LB385D, PT-LB385T, PT-LB355D and PT-LB355T
*2 The wireless module (Model No.: ET-WML100) and the wireless LAN function are not available in Taiwan.
Chapter 7 Appendix - Specications
To Next Page
Loading...
